background image

Lit. No. 76636, Rev. 00 

April 15, 2017

SAFETY PRECAUTIONS

Improper assembly and operation could cause 
personal injury and/or equipment and property 
damage. Read and understand labels, these 
instructions, and the Owner's Manual before 
assembling, operating, or making adjustments.

The machine is intended exclusively for use for 
brushing operations in property maintenance and 
snow clearance. Examples of intended use are: snow 
clearing; sidewalk, driveway and parking lot cleaning 
(with multi-purpose brushes); spring debris clean-up; 
dethatching; clearing debris from arti

fi

 cial turf; and leaf 

clean-up (with multi-purpose brushes). 

NOTE: Lubricate grease 

fi

 ttings after each use. 

Use a good quality multipurpose grease.

SAFETY

SAFETY DEFINITIONS

NOTE: Indicates a situation or action that can lead 
to damage to your rotary broom or other property. 
Other useful information can also be described.

 WARNING

Indicates a potentially hazardous situation 
that, if not avoided, could result in death or 
serious personal injury.

 CAUTION

Indicates a potentially hazardous situation 
that, if not avoided, may result in minor to 
moderate injury. It may also be used to alert 
against unsafe practices.

 WARNING

•  Always make sure personnel are clear of 

areas of danger when using equipment.

•  Before working with the rotary broom, 

secure all loose-

fi

 tting clothing and 

unrestrained hair.

•  Do not climb onto or ride on rotary broom.

 CAUTION

•  Do not operate a rotary broom in need of 

maintenance.

•  Before operating the rotary broom, 

reassemble any parts or hardware removed 
for cleaning or adjusting.

•  Before operating the rotary broom, remove 

materials such as cleaning rags, brushes, 
and hand tools from the rotary broom.

•  Tighten all fasteners according to the 

Torque Chart. Refer to Torque Chart for the 
recommended torque values.

Содержание 74880

















Отзывы: