Western Star 47X 2020 Скачать руководство пользователя страница 115

Страница: 115 / 166

rial. Remove any foreign material. If there is any
evidence that balance weights are missing, re-
move the driveshaft and have it balanced.

For driveshafts with slip joints, check to be sure
the yoke plug is not loose or missing. See

Fig. 6

Repair or replace the yoke plug as needed. If the
yoke plug is missing, the splined shaft may be
hitting the plug and knocking it out; contact your

Regional Service Office for assistance in deter-
mining the correct driveshaft length.

41–02 Driveline Lubrication

Universal Joint Lubrication

NOTE: Vehicles equipped with Meritor RPL Se-
ries drivelines do not require periodic lubrication.

Park the vehicle on a level surface, apply the
parking brakes, and chock the tires.

Wipe all old grease and dirt from each U-joint
grease fitting. See

Fig. 6

Use a hand-type grease gun, or a high-pressure
gun with a low-pressure adapter, to lubricate

f410534

06/02/2016

Yoke

Input Flange

Bolt

Washer

Nut

Fig. 4, Meritor RPL35 Series U-Joint

f410012a

10/06/2016

Attempt to move the sleeve-yoke and splined shaft back
and forth.

Fig. 5, Slip Joint Spline Wear Checking

f410050a

10/07/2016

A. After grease appears, cover the pressure-relief hole

while continuing to lubricate.

Slip Joint Grease Fitting (with grease gun attached)

Yoke Plug

Grease

Half-Round Yoke

Yoke Plug Pressure-Relief Hole

Slip Joint Seal

Full-Round Yoke

U-Joint Grease Fitting

Fig. 6, Slip Joint and U-Joint Lubrication

Driveline

47X and 49X Maintenance Manual, August 2020

41/3

Содержание 47X 2020







































































































































































Результаты поиска

Содержание 47X 2020

Отзывы:

Похожие инструкции для 47X 2020

Бренды по названию

Популярные бренды

Western Star 47X 2020, Руководство по обслуживанию

Результаты поиска

Содержание 47X 2020

Отзывы:

Похожие инструкции для 47X 2020

Бренды по названию

Популярные бренды