manualshive.com logo in svg

Westell ProtectLink VHF-UHF, Инструкция по установке и эксплуатации

Поделиться
Скачать
Westell ProtectLink VHF-UHF Скачать руководство пользователя страница 52

VHF-UHF Bi-Directional Amplifier Installation and Users Guide
Installation Guidelines: 4.8 Controlling the VHF-UHF Bi-Directional Amplifier

WESTELL.COM

1-800-377-8766

Page 4-10

4.8 Controlling the VHF-UHF Bi-Directional Amplifier

Controlling and monitoring the Signal Booster requires that a properly configured 
computer with a web browser is connected via an Ethernet cable, such as the one 
shown in 

Figure 4-3

. 

During installation or maintenance, the Network Interface port of a computer can 
temporarily be connected to the external GUI port on the bottom of the Signal 
Booster. 

Figure 4-3   

Ethernet Cable

Figure 4-4   

GUI port for Ethernet connection

WARNING:

The RJ45 Ethernet port on the external surface of the enclosure is for 
maintenance use only. This port cannot be used as a permanent 
connector.

 

RJ45 Cable Port

Содержание ProtectLink VHF-UHF





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды