Equipment Issue A
030‐101815 Rev. A, February 2014
Section BXM‐10N‐HE5‐20A
R
E
2014 Westell, Inc. All rights reserved.
Westell
r
is a registered trademark of and Boxer
t
is a trademark of Westell, Inc.
1402IARA
Westell
r
Boxer
r
BXM1019‐NHE5
Outdoor Cabinet with ‐48/
+
24VDC Heat Exchanger
CONTENTS
PAGE #
1. GENERAL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. FEATURES 2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3. INSTALLATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4. MAINTENANCE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. SERVICE & REPAIRS
. . . . . . . . . . . . . . . . . . . . . . . .
6. CUSTOMER & TECHNICAL SERVICES
. . . . . . . .
7. WARRANTY & RETURNS
. . . . . . . . . . . . . . . . . . . . .
8. SPECIFICATIONS
. . . . . . . . . . . . . . . . . . . . . . . . . . .
9. APPENDIX A ‐ Product Views
. . . . . . . . . . . . . . . . . .
1.
GENERAL
1.1
Document Purpose
This document provides general, installation, and specifica
tion information for the Westell Boxer
r
BXM1019‐NHE5
Outdoor Cabinet with ‐48/+24VDC Heat Exchanger (shown
in Figure 1). This product is designed to provide Network
equipment protection in outdoor environments while provid
ing a quick and easy customer hand‐off. The intended audience
for this document is engineering, operations, and installation
personnel of MSO, Telco, and utility companies. See Table 4
for product ordering information and available options, as well
as information on the companion but optional battery box or
skirt that can be mounted under the Boxer cabinet.
‐ NOTE ‐
Hereafter, the BXM1019‐NHE5 Boxer cabinet may be referred
to as the “Boxer” or “cabinet.”
1.2
Document Status
Whenever this practice is updated, the reason will be stated in this
paragraph.
1.3
Product Purpose and Description
Boxer is a compact, actively‐cooled, NEMA 4 outdoor cabinet
that can house and protect a wide range of electronic equipment.
Up to 10 vertical RUs (17.5”) of 19‐inch wide internal rack space
is available to house Network equipment such as (but not limited
to) multiplexers, copper bonding solutions, Ethernet switches and
media converters, xDSL boxes, and DS3 hand‐offs.
Protectively mounted on the Boxer front door, separate from
the interior rack space, is a heat exchanger and fan unit. Also
mounted on the door, a controller card features internal fact
ory‐installed wiring for the fans, temperature alarm, door
alarm, and a 5A fan fuse. External wiring from the card to the
power source and alarm monitoring equipment is accom
plished using “Euro‐connector” snap‐in terminal blocks which
Figure 1.
Isometric Closed View of Boxer Cabinet
can be quickly disconnected from the controller card, and later
re‐attached for easy connections.
Boxer supports rapid equipment installation and wiring through
the use of adjustable and removable 19” rack channels. To ensure
easy access for input and out cabling, Boxer includes ample room
below the rack space as well as various sized conduit knock‐outs.
1.4
Product Mounting
The Boxer cabinet is typically mounted outdoors, above
ground, on an H‐frame, or wall. Optional mounting kits are
available to support a round pole (from 8” to 20” in diameter)
or a square pedestal or post (minimum 8” wide). Concrete pad
mounting is supported when used with the optional Boxer bat
tery box or skirt. All mounting hardware must be capable of
supporting the weight of the Boxer cabinet (approximately 70
pounds) plus the weight of any equipment mounted in it. The
Boxer cabinet is typically located at the customer premises but
can be located anywhere a compact, weather‐tight, outdoor
cabinet is required.
1.5
Product Features
Each Boxer cabinet comes fully assembled, pre‐wired, tested,
and ready for field‐provided customer equipment installation,
and includes the following features and capabilities.
S
NEMA 4 compliant
S
Conforms to ANSI/UL 60950‐1 and certified to CAN/CSA
C22.2 No. 60950‐1
S
Conforms to ANSI/UL 60950‐22 and certified to CAN/
CSA C22.2 No. 60950‐22
S
FCC Part 15
S
Actively cooled with heat exchanger
S
Dissipates up to 400 watts of internally‐generated heat
