WESTCAR ROTOMEC ALFA Скачать руководство пользователя страница 22

Страница: 22 / 84

o w e r

r a n s m i s s i o n

2.3 SAFETY DEVICES AND SIGNALLING PLATES

CAUTION

Before commissioning and operating the ROTOMEC hydromechanics coupling, make sure

that signal- ling plates and all safety and temperature control devices are correctly installed, used

and are efficient; if not, restore good working conditions before going on with installation and use.

POS.

DESCRIPTION

SLINGING DEVICES FOR LIFTING:

They enable lifting through grip and slinging points and safe handling of the

hydromechanic coupling.

DM ASSEMBLY DEVICE:

It enables the safe fitting of the hydromechanic coupling fitting on the drive end shaft.

DISASSEMBLY DEVICE “VE” or “SE”:

It enables the safe, removal of the hydromechanic coupling from the driving

shaft.

DEVICES FOR COUPLING CLAMPING ON “TT” DRIVE SHAFT:

They enable to safely fix the hydromechanic

coupling

FUSIBLE PLUG “TF”:

It detects any leakage of transmission fluid from the hydromechanic coupling and any drive

failure at the driven machine, when the maximum temperature of the fitted TF is exceeded.

EXPANDABLE TRIP PLUG “TE”:

It permits to detect the overheating value as set up in the fitted TE through release

of the signalling stud by a suitable microswitch, which shall be of “ET” type for standard and “ETA” type for ATEX

manufacture.

PLUG WITH thermocouple AND RPM CONTROLLER “PM” with “T09”:

It permits to detect the maximum

temperature of the fitted PM plug and to transmit an electromagnetic pulse signal, which is detected by suitable

sensor and sent to the electronic control unit, which in turn compares the rpm with the threshold setpoint.

DEVICE FOR OVERLOAD CONTROL “SCD”:

It detects the output rotation speed of the coupling. This SCD device

is composed of an rpm controller, which receives a pulse train through a sensor and generates a signal for alerting

and stopping the system in case of extreme speed reduction.

CAUTION

ATTENTION

art

2 - W

arningS

reScriPtionS

ROTOMEC

and

aintenance

andbook

Содержание ROTOMEC ALFA





















































































Результаты поиска

Содержание ROTOMEC ALFA

Отзывы:

Бренды по названию

Популярные бренды

WESTCAR ROTOMEC ALFA, Оригинальное руководство пользователя

Результаты поиска

Содержание ROTOMEC ALFA

Отзывы:

Бренды по названию

Популярные бренды