9
8
DIAGRAM OF THE CONSOLE
The console
offers six modes
that provide
instant exercise
feedback. Each
mode is dis-
played for five
seconds in a
repeating cycle.
The modes are
described below.
Pulse—This mode displays your heart rate
when the pulse sensor is used.
Calorie—This mode displays the approximate
number of calories you have burned.
Fat Calorie—This mode displays the approxi-
mate number of fat calories you have burned.
(See Burning Fat on page 10.)
Speed—This mode displays your pedalling
speed, in kilometres per hour.
Time—This mode displays the length of time
you have exercised.
Distance—This mode displays the total number
of kilometres you have pedalled during your
workout.
HOW TO OPERATE THE CONSOLE
1. To turn on the
power, press the
on/reset button
or simply begin
pedalling. When
the power is
turned on, the
entire display will appear for two seconds. The con-
sole will then be ready for operation.
2. When the power
is turned on, the
console will
begin displaying
all modes in a
repeating cycle
(except for the
pulse mode). Flashing arrows will show which
mode is currently displayed.
3. To measure your
pulse, stop ped-
alling and place
your thumb on
the pulse sensor
as shown. The
pulse sensor is
pressure-activat-
ed—fully press down the pulse sensor. Do not
press too hard, or the circulation in your thumb
will be restricted, and your pulse will not be
detected. Next, slightly raise your thumb until the
heart-shaped indicator in the display flashes
steadily. Hold your thumb at this level. After 5 to 10
seconds, three dashes will appear in the display
and your pulse will then be shown. Hold your thumb
on the sensor for another 15 seconds for the most
accurate reading. If the displayed pulse appears to
be too high or too low, or if your pulse is not dis-
played, lift your thumb off the sensor and allow the
display to reset. Press down again on the sensor as
described above.
Make sure that your thumb is positioned as shown,
and that you are applying the proper amount of pres-
sure to the pulse sensor. Try the sensor several
times until you become familiar with it.
4. To reset the display, press the on/reset button.
5. To turn off the power, simply wait for about six
minutes. Note: The console has an “auto-off”
feature. If the pedals are not moved and the con-
sole buttons are not pressed for six minutes, the
power will turn off automatically in order to con-
serve the batteries.
Arrow
HOW TO USE THE PURSUIT 795i
HOW TO ADJUST THE SEAT
For effective exer-
cise, the Seat (19)
should be at the
proper height. As
you pedal, there
should be a slight
bend in your knees
when the pedals
are in the lowest
position. To adjust
the Seat, first hold
the Seat and
unscrew the Seat
Knob (29). Align
one of the holes in
the Seat Post (20)
with the hole in the
Frame (15). Insert
the Seat Knob into the Frame and the Seat Post, and
tighten the Seat Knob into the Frame. Caution: Make
sure to insert the Seat Knob through one of the
holes in the Seat Post; do not insert the Seat
Knob under the Seat Post.
HOW TO ADJUST THE PEDALLING RESISTANCE
To vary the inten-
sity of your exer-
cise, the ped-
alling resistance
can be adjusted.
The resistance is
controlled with
the Resistance
Knob (10). To
increase the
resistance, turn
the Resistance
Knob clockwise;
to decrease the
resistance, turn
the Resistance Knob counterclockwise.
HOW TO APPLY AN INFORMATION DECAL TO
THE CONSOLE
All of the infor-
mation on the
console is printed
in English. The
included decal
sheet contains
the same infor-
mation in five
other languages.
If English is not
your language,
find the decal on
the decal sheet
that is printed in
your language.
Next, peel the
information decal
off the decal
sheet. Apply the
decal to the
console in the
location shown.
BATTERY INSTALLATION
Before the console can be operated, two 1,5V
batteries must be installed. If you have not installed
batteries, see assembly step 2 on page 6.
19
20
15
29
10
Decal
