5
8
Next, locate the Reed Switch (49). Turn the Crank
(22) until the Magnet (4) is aligned with the Reed
Switch. Loosen but do not remove the M4 x 16mm
Screw (46). Slide the Reed Switch slightly closer to or
away from the Magnet. Retighten the Screw. Turn the
Crank for a moment. Repeat until the console dis-
plays correct feedback. When the Reed Switch is cor-
rectly adjusted, re-attach the left side shield and
pedal.
HOW TO ADJUST THE RESISTANCE STRAP
If there is not enough pedalling resistance when the
resistance knob is turned to the highest setting, the
Resistance Strap (15) may need to be adjusted. To
adjust the Resistance Strap, the left side shield must
first be removed. Refer to the instructions on page 7
and remove the left side shield.
Next, turn the
resistance knob
to the lowest set-
ting. Locate and
open the Strap
Clamp (38). Grip
the end of the
Resistance Strap
(15) and pull it
up slightly. While
holding the end
of the Resistance Strap,
fully
close the Strap Clamp.
Turn the Crank (22) for a moment to make sure that
there is not too much resistance. When the
Resistance Strap is properly adjusted, re-attach the
left side shield and pedal.
HOW TO ADJUST THE DRIVE BELT
The exercise cycle features a drive belt that must be
kept properly adjusted. If the belt causes excessive
noise or slips as you pedal, the belt should be
checked. To do this, the side shields must first be
removed. Refer to the instructions on page 7 and
remove the left side shield. Next, remove the right
side shield in the same way.
Press down on
the centre of the
Drive Belt (14)
between the front
and rear pulleys.
There should be
from 6mm to
13mm of move-
ment in the cen-
tre of the Belt.
If the Drive Belt
(14) is properly
adjusted, re-
attach the side
shields and ped-
als. If the Belt
needs to be
adjusted, loosen
the Nylon
Locknut (7) on
the left side of
the Flywheel
(29). To tighten the Belt, turn the M10 Nut (30) clock-
wise; to loosen the Belt, turn the M10 Nut counter-
clockwise. Make sure that the Flywheel is straight and
tighten the Nylon Locknut (7). Re-attach the side
shields and pedals.
4
22
30
14
Top View
Top View
14
7
29
4
5
4. Slide the Handlebar Collars (12) onto the
Handlebars (6). Attach the Handlebars to the
Scissor Frame (3) with four M6 Button Head Bolts
(19) and four M6 Locknuts (52). Next, slide the
Handlebar Collars over the Button Head Bolts.
5. The Console (48) requires two 1,5V batteries (not
included). Alkaline batteries are recommended.
Refer to the inset drawing. Remove the battery door
from the Console. Press two batteries into the bat-
tery compartment.
Make sure that the negative
ends of the batteries (marked ÒÐÓ) are touching
the springs in the battery compartment.
Re-
attach the battery door.
Connect the console wire to the Reed Switch Wire
(49).
Slide the Console (48) onto the console plate. Make
sure that the plastic clip on the back of the Console
snaps into the tab on the console plate.
Note: The console on your exercise cycle may
not look like the one pictured, but it will function
the same way.
Battery Door
Batteries
6
12
52
19
19
3
48
Console
Plate
49
Console
Wire
22
8
6
6. Identify the Left Pedal (8). (The Left Pedal is
marked with an ÒL.Ó) Using an adjustable wrench,
tighten the Left Pedal
counterclockwise
into the left
arm of the Crank (22).
Tighten the Right Pedal (not shown)
clockwise
into
the right arm on the Crank.
7.
Make sure that all parts are properly tightened before you use the exercise cycle.
Place a mat under
the exercise cycle to protect the floor or carpet. Note: Some hardware may be left over after assembly is
completed.
49
22
46
38
15