background image

10

HOW TO USE THE WESLO

¨

ECLIPSE

HOW TO EXERCISE ON THE ECLIPSE

To mount the ECLIPSE, pin the handlebars in the sta-
tionary position, hold the handlebars, and step onto
the pedal that is in the lowest position. Next, step onto
the other pedal. Push the pedals until they begin to
move with a continuous motion. 

Note: The crank can

turn in either direction; it is recommended that
you turn the crank in the direction shown below; 
however, to give variety to your exercise, you may
choose to turn the crank in the opposite direction. 

To dismount the ECLIPSE, allow the pedals to slowly
come to a stop. 

CAUTION: The ECLIPSE does not

have a freewheel; the pedals will continue to
move until the flywheel stops. 

When the pedals are

stationary, step off the highest pedal first. Then, step
off the lowest pedal.

HOW TO ADJUST THE RESISTANCE OF THE 
PEDALS

As you exercise,
you can adjust
the resistance of
the pedals with
the resistance
knob mounted
on the upright.
To increase the
resistance, turn
the knob clock-
wise; to
decrease the
resistance, turn
the knob counterclockwise.

HOW TO USE THE HANDLEBARS IN THE 
STATIONARY POSITION

To focus on lower-body exercise, the handlebars can
be pinned in a stationary position. To do this, align the
holes in the handlebars with the hole in the handlebar
post. Next, insert the lock pin through the handlebars
and the handlebar post (see the drawing below).
Note: If it is difficult to insert the lock pin, twist the
handlebars slightly in order to align the holes; 

do not

twist the handlebars too far or they may be dam-
aged

. Next, tighten the resistance knob.

HOW TO USE THE HANDLEBARS IN THE 
DUAL-MOTION POSITION

To add upper-body exercise to your workout, remove
the lock pin from the handlebars and the handlebar
post (see the drawing above). 

Keep the lock pin in a

safe place.

The resistance of the handlebars can be

adjusted with the resistance knob. To increase the
resistance, turn the knob clockwise; to decrease the
resistance, turn the knob counterclockwise.

To exercise, move the handlebars forward and back-
ward as you pedal. Be sure to keep your back straight
and your knees bent slightly.

Pedal

Crank

Pedal

Resistance Knob

Upright

Handlebars

Resistance Knob

Lock Pin

Содержание Eclipse

















Отзывы: