background image

6

3. If there are plastic ties in the brackets on the Handrails

(4), remove the plastic ties. Hold one of the Handrails
near the right Upright (38) as shown. Insert the Wire
Harness (53) up through the bracket on the Handrail and
out of the round hole in the side of the Handrail. If nec-
essary, use needlenose pliers to pull the Wire Harness
out of the hole. 

Be careful not to damage the Wire

Harness. 

Insert the brackets on the Handrails (4) into the upper
ends of the Uprights (38).

Finger tighten four 1” Bolts (16) with Handrail Washers
(40) into the Uprights (38) and the Handrails (4) as
shown.

40

53

38

40

38

Connectors

16

40

16

4

16

4

16

Bracket

3

5

Plastic Ties

5

4

4

53

87

4

4. Set the Console Base (87) on the Handrails (4). Thread

four 3/4” Screws (5) into the Handrails and the Console
Base. After you have started all four Screws, 

tighten the

Screws until they are snug; do not overtighten the
Screws. 

Note: It may be helpful to press down on the

top of the Console Base above the Handrails as you
tighten the Screws.

See step 3. Firmly tighten, but do not overtighten,
the four 1” Bolts (16).

Insert the Wire Harness (53) through the two indicated
plastic ties on the Console Base (87) and up through the
hole in the Console Base as shown.

5. Hold the Console (11) near the Console Base (87).

Touch the right Handrail (4) to discharge any static.

Next, insert the Wire Harness (53) through the plastic tie
labeled C in the drawing at the right.

Locate the two connectors on the Wire Harness (53).
Plug the wider connector into the connector labeled A in
the drawing at the right (see drawing 5b). 

The connec-

tors should slide together easily and snap into
place

. If they do not, turn the connector on the Wire

Harness and try again. Insert the other connector
through the plastic tie labeled D; plug the connector into
the connector labeled B (see drawing 5c). 

IF THE CON-

NECTORS ARE NOT INSERTED PROPERLY, THE
CONSOLE MAY BE DAMAGED WHEN THE POWER
IS TURNED ON.

See drawing 5a. Pull any slack in the Wire Harness (53)
through the two ties. Make sure that the end of the Wire
Harness indicated by the arrow is routed as shown.

Securely tighten the plastic ties around the Wire
Harness.

Cut off the end of each plastic tie. 

4

5

87

11

B

Tie

A

5b

53

A

B

5c

53

53

Tie

5a

53

Tie C

Tie D

Содержание Cadence 255 Dr Treadmill




















Отзывы: