background image

7

EN

However, there is no guarantee that interference will not 
occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and 
on, the user is encouraged to try to correct the interference 
by one or more of the following measures:
•   Reorient or relocate the receiving antenna.
•   Increase the separation between the equipment and 

receiver.

•   Connect the equipment into an outlet on a circuit 

different from that to which the receiver is connected.

•   Consult the dealer or an experienced radio/TV 

technician for help.

SYMBOLS 

To reduce the risk of injury, user must read 
instruction manual

Warning

Wear ear protection

Wear eye protection

Wear dust mask

Li-Ion battery,  battery must be recycled

Do not burn

Batteries may enter water cycle if disposed 
improperly, which can be hazardous for 
ecosystem. Do not dispose of waste batteries as 
unsorted municipal waste.

POSITEC Inc. has established a partnership with 
the RBRC Corporation to recycle any Positec 
batteries with the RBRC-call2recycle seal. For 
environmental protection, please do not discard 
batteries in the trash. After the batteries’ life 
cycle is ended, then please call 1-800-822-
8837 for a free service that will properly dispose 
of the battery.

Содержание CDT118W













Отзывы: