Wesco 272152 Скачать руководство пользователя страница 7

Page

 

7

 

of

 

14

 

 

© Copyright 2016 WESCO Industrial Products, Inc. Specifications subject to change. Not responsible for errors or omissions. 

  

 

6. TROUBLE SHOOTING

 

 

No 

Problem Causes 

Solutions 

Forks cannot lift to 

maximum height

 

There is not enough hydraulic oil. 

- Pour in hydraulic oil. 

 

Forks cannot  lift 

up 

- No hydraulic oil. 
 
- The oil has impurities. 
 
- The Adjusting Nut (104S) is too high, 

keeping the pumping valve open. 

 
- Air enters the hydraulic system.

- Refill the hydraulic oil. 
 
- Change the oil. 
 
- Adjust the nut (104S) or screw (318S) 

(see item 3.4) 

 
- Remove the air.(see item 4.2) 

Forks cannot be 

lowered 

- The Piston Rod (328) or Pump Body 

(322S) is deformed resulting from partial 
loading slanting to one side or over-
loading. 
 

- The fork was kept in a high position for 

an extended amount of time. The piston 
rod bore to arise in rusting and jamming 
of the rod. 

 
- The Adjusting Nut (104S) or Screw 

(318S) is not in correct position. 

- Replace the Piston Rod (328) or 

Pump Body (322S). 

- Keep the fork in the lowest position if 

not using, and pay more attention to 
lubricate the rod. 

- Adjust the Nut (104S) or Screw (318S) 

(see item 3.3) 

Leaks 

- Sealing parts worn or damaged. 
 
- Some part cracked or worn down. 

- Replace with the new parts.  
 
- Replace with the new part. 

Forks lowers 

without the 

release valve 

working 

- Impurities in the oil prevent the release 

valve from closing. 

 

Some part/s of hydraulic system are 
cracked or bored. 

 
- Air enters the hydraulic system. 
 

- Sealing parts worn or damaged. 

 

The Adjusting Nut (104S) or Screw 
(318S) is not in the correct position. 

- Replace with new oil. 
 
 

Inspect and replace the damaged 
part/s. 

 
- Remove the air. (See item 4.2) 
 
- Replace with the new parts. 
 
- Adjust the nut (104S) or screw (318S). 

(See item 3.2) 

 

NOTE: DO NOT ATTEMPT TO REPAIR THE PALLET TRUCK UNLESS YOU ARE TRAINED 

AND AUTHORIZED TO DO SO.

 

 

 

 

 

 

 

 

 

Stainless Steel Pallet Truck 

(Part # 272152)  

Instruction Manual 

 

ATTENTION: TO INSURE SAFE AND EASY USE OF YOUR WESCO PALLET 

TRUCK, READ THESE INSTRUCTIONS ENTIRELY BEFORE USING. 

Industrial Products, Inc. 

Содержание 272152















Отзывы: