out so as to limit the risk and the height of a fall. For safety reasons, it is important to be careful to minimise the distance and risk
of falling while working. Whenever possible, we recommend setting the anchorage point above the user.
It is imperative to connect the scaffold hook(s) to the anchor point of the structure, and the energy absorber of the lanyard MUST
be connected to the attachment point of the harness, the use the other way around is FORBIDDEN.
[!] Lanyards without energy absorbers must not be used as fall arrest systems.
[!] An energy absorber with a lanyard and its connectors should not exceed 2 metres in length.
[!] A Lanyard with energy absorber up to 2 m must not be extended with other components (lanyards, …), it is ONLY
possible to add connectors at each end (provided that the lanyard is not equipped with connectors beforehand).
*It is essential for safety reason to verify the clearance at the work place before each use and during use in order to be sure there
will be no collision with the ground or obstacle in case of fall. Take particular attention to obstacles in movement (for example truck,
mobile work platform, etc.).
During use, take care of the amount of slack in the lanyard near a fall hazard. Take care not to move into an area where there is
risk of fall.
An energy-absorbing lanyard cannot be used choke hitched.
Two separate lanyards, each with an energy absorber, should not be used side-by-side as a forked lanyard. The unused end of the
forked lanyard combined with an energy absorber should not be hooked to your harness, for the energy absorber may not play its
part in case of fall.
Before and during use, we recommend that you take every precaution necessary for an eventual safe rescue.
This equipment is for the sole use of people trained, skilled and in good health, or under the supervision of a trained and skilled
person.
Warning! Certain medical conditions may affect user safety. If in doubt, consult your doctor.
Be aware of the hazards that could reduce the performance of your equipment, and therefore the user’s safety, if exposed to
extreme temperatures (<-30°C or >50°C), prolonged exposure to the elements (UV rays, humidity), chemical agents, electrical
constraints, twisting of the fall arrest system during use, sharp edges, friction or cutting, etc.
Check the condition of the energy absorbing lanyard before every use: visual inspection to check the condition of the straps/ropes
(no signs of cuts, burns or abnormal shrinkage), the seams (no visible damage), the metal parts (no deformation or rust) and that
the connectors work properly and the absorber has not been activated. The transparent sleeve of the energy absorber must be
present and not damaged. Product markings must remain legible. In the event of doubt regarding the condition of the device, or
after a fall, the energy absorbing lanyard must not be reused, should be withdrawn from service (marking it with the words “DO
NOT USE” is recommended) and must be returned to the manufacturer or to a qualified person appointed by the manufacturer.
It is forbidden to add, to remove or replace any energy absorber component whatsoever.
Temperature: use the equipment between - 30°C and + 50°C to avoid affecting its operation.
Chemical products: remove the lanyard from service should it be exposed to chemical products, solvents or combustible materials
that could affect its operation.
TECHNICAL DATA: Material: polyamide and/or polyester – Breaking strength > 15 kN.
SUITABILITY FOR USE:
The energy absorbing lanyard must be used with a fall arrest system as defined in the product data sheet (see standard EN363)
to guarantee that the dynamic force exerted on the user during the arrest of a fall is max. 6 kN. A fall arrest harness (EN361) is the
only body-gripping device that may be used. It may be dangerous to create one’s own fall arrest system where each safety function
can interfere with another safety function. Read the recommendations on using each component in the system before use.
VERIFICATION PROCEDURE:
Service life of the product is 10 years (in accordance with the annual examination by a competent person authorized by Werner
UK Sales & Distribution Ltd.), although its actual service life may be longer or shorter, depending on its usage and/or annual
inspection results. The product must be checked systematically in case of doubt or after a fall and at least every year by the
manufacturer or his authorised representative, in order to guarantee its resistance and thus the safety of the end-user.
The product data sheet should be completed (by writing) after each verification; date of inspection and date of next inspection must
be indicated on the data sheet, it is also recommended to put date of next inspection on the product.
SERVICING AND STORAGE: (Comply strictly with these instructions)
During transport, keep the energy absorber in its packaging, well away from any cutting surface. Clean it with water, wipe it with a
rag and hang it up in a well ventilated location, to let it dry naturally and away from a naked flame or heat source; follow the same
procedure for components that have become damp during use. The energy absorber should be stored in its packaging in a warm,
dry, ventilated place, protected from sunlight, heat and chemicals.
TOTAL LENGTH OF EQUIPMENT:
2m
Equipment reference number
79208
Fall factor
2
Fall clearance of the PPE
6.50m
