Wenger UltraStor Cover Panel Скачать руководство пользователя страница 1

Installation Instructions

UltraStor

™ 

Cover Panel

Note:

Please read and understand these instructions before assembling the parts.

Note:

Remove all items from the shipping cartons and arrange them in a convenient location. 

Refer to the illustrations on the following pages. 

If you need additional information, contact Wenger Corporation using the information below.

C

ONTENTS

Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . .2

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Manufacturer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Intended Use  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Warranty  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Required Tools  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Fastener Parts List  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Cover Panel Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

End Cover Panel Installation  . . . . . . . . . . . . . . . . . . . . .4

Center Cover Panel Installation  . . . . . . . . . . . . . . . . . . .7

Replacement Parts List  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

©Wenger Corporation 2015

Printed in USA 12/15

Part #250C880-02

Wenger Corporation,

555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448

Questions? Call.....USA: (800) 4WENGER (493-6437) • Worldwide: +1(507) 455-4100 • www.wengercorp.com

Содержание UltraStor Cover Panel









Отзывы: