background image

4

GENERAL SAFETY RULES

Safety is a combination of common sense, staying alert, and knowing how your item works. 

SAVE THESE SAFETY INSTRUCTIONS. 

WORK AREA SAFETY

1. Keep work area clean and well lit. Cluttered or dark areas invite accidents.

2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable 

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

3. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the 

risk of electric shock.

4. Keep children and bystanders away while operating a power tool. Distractions can cause you to 

lose control.

ELECTRICAL SAFETY

1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter 

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk 

of electric shock.

2. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and 

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

3. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep 

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk 

of electric shock.

4. If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter 

(GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.

PERSONAL SAFETY

1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do 

not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A 

moment of inattention while operating power tools may result in serious personal injury.

2. Use personal protective equipment. Always wear eye protection. Protective equipment such as a 

dust mask, non-skid safety shoes and hearing protection used for appropriate conditions will reduce 

the risk of personal injury.

3. Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from 
moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.

      WARNING:

 Read and understand all warnings, cautions and operating instructions before 

using this tool. Failure to follow all instructions listed below may result in personal injury and 
tool damage.

Содержание LA8800













Отзывы: