Wen CT1065 Скачать руководство пользователя страница 24

Страница: 24 / 28

MAINTENANCE

CAUTION

Most plastics are susceptible to damage

from various types of commercial solvents. Do not

use any solvents or cleaning products that could

damage the plastic parts. Some of these include but

are not limited to: gasoline, carbon tetrachloride,

chlorinated cleaning solvents, and household deter-

gents that contain ammonia.

NOTE:

Electric tools used on fiberglass material, wall-

board, spackling compounds, or plaster are subject to

accelerated wear and possible premature failure because

the fiberglass chips and grindings are highly abrasive to

bearings, brushes, commutators, etc. Consequently, we

do not recommend using this tool for extended work on

these types of materials. However, if you do work with

any of these materials, it is extremely important to clean

the tool using compressed air after operation.

CLEANING & STORAGE

1. Keep the ventilation openings free from dust and de-

bris to prevent the motor from overheating.

2. Wipe the tool surfaces clean with a clean cloth. Make

sure water does not get into the tool.

Fig. 23

3. Store the tool in a clean and dry place away from the

reach of children. Store in temperatures between 41° to

86°F.

4. Cover the track saw in order to protect it from dust

and moisture. It is preferable to store it in its original

packaging with the instruction manual and all accesso-

ries.

LUBRICATION

The bearings of your track saw are permanently sealed

and require no extra lubrication. The gearbox is also suf-

ficiently lubricated from the factory and requires no ad-

ditional lubrication.

PRODUCT DISPOSAL

Used power tools should not be disposed of together

with household waste. This product contains electronic

components that should be recycled. Please take this

product to your local recycling facility for responsible

disposal and to minimize its environmental impact.

Please recycle the packaging where facilities exist.

CARBON BRUSH REPLACEMENT

The wear on the carbon brushes depends on how fre-

quently and how heavily the tool is used. To maintain

maximum efficiency of the motor, we recommend in-

specting the two carbon brushes every 60 hours of op-

eration or when the tool stops working. Your track saw

comes with a carbon brush replacement set.

NOTE:

Replacement carbon brushes (Part No. CT1065-

031) can be ordered at

wenproducts.com

. Only genu-

ine WEN replacement brushes designed specifically for

your tool should be used. Carbon brushes are not cov-

ered under the two-year warranty.

1. Unplug the saw. To access the carbon brushes, re-

move the carbon brush cover (Fig. 23) with a flat-head

screwdriver (not included).

2. Carefully remove the old carbon brushes using pliers.

Keep track of which orientation the old carbon brushes

were in to prevent needless wear if they will be rein-

stalled.

3. Measure the length of the brushes (Fig. 23). Install the

new set of carbon brushes if either carbon brush length

is worn down to 3/16" or less. Reinstall the old carbon

brushes (in their original orientation) if your brushes

are

not

worn down to 3/16" or less. Both carbon brushes

should be replaced at the same time.

4. Replace the carbon brush cover.

NOTE:

New carbon brushes tend to spark for a few min-

utes during the first use as they wear down.

Carbon

Brush

Length

CarbonBrush

Cover

Содержание CT1065





























Результаты поиска

Содержание CT1065

Отзывы:

Похожие инструкции для CT1065

Бренды по названию

Популярные бренды

Wen CT1065, Инструкция по эксплуатации

Результаты поиска

Содержание CT1065

Отзывы:

Похожие инструкции для CT1065

Бренды по названию

Популярные бренды