background image

9

UNPACKING

With the help of a friend or trustworthy foe, carefully remove the engraver from the packag-

ing. Do not discard the packaging until all of the parts below are accounted for. If any part is 

damaged or missing, please contact our customer service at (800) 232-1195, M-F 8-5 CST 

or email us at [email protected]

TOOL PURPOSE

The engraver can be used to permanently mark metal, glass, plastic, wood, leather, ceram-

ics and much more. Refer to the diagram below to become familiarized with the parts and 

controls of your engraver.

INCLUDED ACCESSORIES

•  Carbide Tip (1)

•  1.5 mm Hex Wrench (1)

•  Stencil (2)

Carbide Tip

Power Switch

Depth Adjustment Knob

KNOW YOUR ENGRAVER

INSTALLING AN ENGRAVER TIP

1. Loosen the tip locking screw (Fig. 1) by turning it coun-

terclockwise with the included hex wrench.

2. To fit the new engraving tip, insert the tip into the chuck 

ensuring the tip fully enters the chuck. A new tip should 

protrude from the end of the housing by approximately 8.5 

mm (~3/8 inch).

3. Tighten the tip locking screw fully by rotating in a clock-

wise direction.

Fig. 1 

ASSEMBLY

       WARNING:

 Disconnect the engraver from the power supply before making any adjust-

ments or maintenance procedures.

Содержание 21D













Отзывы: