AGENCY LISTING INFORMATION
INSTALLATION
4
NOTE:
DO NOT discard
the carton or other packing
materials until you have
inspected the appliance for
hidden damage and tested it
for proper operation.
Refer to
SHIPPING DAMAGE
CLAIM PROCEDURE
on the
inside front cover of this
manual.
IMPORTANT:
This is a
GENERAL GUIDE. For
specific equipment and
cutout dimensions, and other
installation details, refer to
the
Installation Instructions
supplied with the appliance.
IMPORTANT:
Water damage
caused by failure to set
Wellsloks, failure to install
gasket, or failure to seal flange
to counter is
NOT
covered by
warranty.
UNPACKING & INSPECTION
Carefully remove the appliance from the carton. Remove all protective
plastic film, packing materials and accessories from the appliance
before connecting electrical power or otherwise performing any
installation procedure.
Carefully read all instructions in this manual and the
Installation
Instruction Sheet
packed with the appliance before starting any
installation.
Read and understand all attached labels and diagrams.
Carefully account for all components and accessories before discarding
packing materials. Store all accessories in a convenient place for later
use.
CUT-OUT AND INSTALLATION
Cutouts
a.
Griddles may be installed in METAL COUNTERS ONLY.
b.
Cutout dimensions for griddles and control panels are listed on
the
Installation Instructions
provided with the griddle.
c.
Refer to the
Installation Instructions
for Underwriters
Laboratories
Conditions of Acceptability.
Mounting the griddle:
a.
Verify that provided sealants are applied to the under side of
the griddle top flange prior to setting the unit into the cutout.
b.
After installation, verify that the tabs on the Wellsloks are
turned out to lock the appliance into the counter (see Fig. 2).
c.
Apply a thin bead of food-grade silicone sealant around the
flange to seal it to the counter.
Refer to the
Installation Instructions
for required clearances. Maintain
required clearances between the appliance and adjacent combustible
and non-combustible surfaces.
Sufficient overhead clearance must be provided to allow the element
assembly to be raised. Refer to the
Installation Instruction Sheet
for
required clearances.
Avoid storing flammable or combustible materials near the appliance.
This includes gasoline and other fuels, mops, rags and wrapping paper.
Fig. 2 Set the Wellslloks
This appliance conforms to NSF Standard 4 for sanitation only if
installed in accordance with the supplied
Installation Instructions.
This appliance is Underwriters Laboratory recognized ( ). Since this
appliance is only a single component of a complete installation, the
finished installation of this unit requires additional evaluations to
Underwriters Laboratory standards.
Refer to
Installation Instructions
included with the appliance for
Underwriters Laboratories conditions of acceptability, electrical
requirements and other installation concerns.
STD 4
11
1 p/n
2M-303340
OpManual Built-In Electric Griddles
Содержание G-136
