background image

This appliance is intended for use in commercial establishments 
only. 

 

This appliance is intended to prepare food for human consumption.  
No other use is recommended or authorized by the manufacturer or its 
agents.

 

 

Operators of this appliance must be familiar with the appliance use, 
limitations and associated restrictions.  Operating instructions must be 
read and understood by all persons using or installing this appliance.

 

 

Cleanliness of this appliance is essential to good sanitation.  Read and 
follow all included cleaning instructions and schedules to ensure the 
safety of the food product. 

 

Disconnect this appliance from electrical power before performing any 
maintenance or servicing. 

 

DO NOT submerge this appliance in water.  This appliance is not jet 
stream approved.  Do not direct water jet or steam jet at this appliance, 
or at any control panel or wiring.  Do not splash or pour water on, in or 
over any controls,  control panel or wiring.   Do not wash floor around 
this appliance with water or steam jet. 

 

Exposed surfaces of this appliance can be hot to the touch and may 
cause burns. 

 

Griddle surfaces will be very hot when in use.  Contact will cause      
severe injury. 

 

Do not operate this appliance if the keypad section of the control panel 
is torn or broken.  Call your Authorized Wells Service Agent for service.

 

 

The technical content of this manual, including any wiring diagrams, 
schematics, parts breakdown illustrations and/or adjustment 
procedures, is intended for use by qualified technical personnel. 

 

Any procedure which requires the use of tools must be performed by a 
qualified technician. 

 

This manual is considered to be a permanent part of the appliance.  
This manual and all supplied instructions, diagrams, schematics, parts 
breakdown illustrations, notices and labels must remain with the 
appliance if it is sold or moved to another location. 

 

This appliance is made in the USA.  Unless otherwise noted, this 
appliance has American sizes on all hardware.

 

WARNING: 

Electric 
Shock hazard 

 

All servicing requiring 
access to non-insulated elec-
trical components must be 
performed by a factory au-
thorized        technician. 
DO NOT open any access 
panel which requires the use 
of tools.  Failure to 
follow this warning can 
result in severe electrical 
shock. 

 

WARNING: 

BURN HAZARD 
 

Griddle surfaces will be very 
hot when in use.  Contact will 
cause severe injury.

 

 

CAUTION: 

Risk of 
Damage 

 

DO NOT connect or 
energize this appliance 
until all installation 
instructions are read and 
followed.  Damage to the 
appliance will result if 
these instructions are not 
followed. 

 

CAUTION: 

Hot Surface 

 

Exposed surfaces can be hot 
to the touch and may cause 
burns. 

PRECAUTIONS AND GENERAL INFORMATION 

Содержание FT-18M

















Отзывы: