background image

Set the time with 

MENU 3 

(increase) and 

MENU 4 

(decrease).  Press 

TEMP

 to save the time. 

 

The display will now advance to show zone temperature setpoints: 
              1.450 = Zone 1 @ 450ºF 
              2.450 = Zone 2 @ 450ºF 
              3.450 = Zone 3 @ 450ºF 
              4.450 = Zone 4 @ 450ºF 

 

 
 
 
 
 
 
 
 
 
 
 
 
Set the temperature setpoint for Zone 1 with 

MENU 3 

(increase) and 

MENU 4 

(decrease).  Press 

TEMP 

to advance to next zone.  

Repeat for Zone 2,  Zone 3, and Zone 4. 

 

Press 

TEMP

 to exit program mode for 

MENU 1

 key.  The LED will stop 

flashing. 

 

MENU 2

MENU 3

 and 

MENU 4

 program in a similar manner, except 

that the programming mode is entered by pressing TEMP and the       
desired 

LEFT MENU 

key for 3 seconds. 

 

PROGRAMMING TIME (RIGHT SECTION) 

 

Press and hold TEMP.  While holding TEMP, press and hold the desired 

RIGHT MENU 

key for 3 seconds.  The LED above the menu key will 

glow, and the display will read “_ _ : _ _”, prompting you to enter the 4-
digit access code. 

 

Enter the 4-digit code.  Starting with the first digit, the bottom bar of the 
display moves to the top bar.  The security code does not show on the 
display.  Once the correct code is entered, the display changes to the 
preset time, and the LED for that MENU key flashes. 

 

When in program mode, the timer is displayed as 4 digits (i.e. 00:15).  In 
regular mode, the timer is displayed as 3 digits (i.e. _0:15).  Set the time 
with MENU 3 (increase) and MENU 4 (decrease). 

 

Press the TEMP key to save the time and exit program mode for this 
MENU key.  The LED will stop flashing. 

When in program mode, the 
timer is displayed as 4 digits 
(i.e. 00:15).  In regular mode, 
the timer is displayed as 3 
digits (i.e. _0:15).   
 
 
 
 

NOTE:

  The manufacturer 

advises that product finishing 
be controlled with 

time

, and 

that MENU 1 - 3 all use  the 
same temperature setpoint. 
The timer is disabled any time 
the actual temperature is not 
at setpoint, and the time     
required to reach the new 
temperature (up or down) 
may be  unacceptable. 
 
NOTE:  

LEFT

 

MENU 4 

should be programmed for 
275º and reserved for 
CLEANING.   
 
While in program mode, if no 
keystroke is detected within 
15 seconds, control reverts to 
normal operation.  If no       
access code, or the wrong    
access code, is entered,     
control reverts to normal    
operation. 

MAINTENANCE PROCEDURES (continued) 

Содержание FT-18















Отзывы: