background image

 

                                      -                                                                      11 - 

 

 

 

 

 
 

 

 
 

 

When Heater is ON

Emitter screen will become bright red due to intense heat. The color is more visible at night. Burner will display 

tongues of blue and yellow flame. These flames should not be yellow or produce thick black smoke, indicating an 
obstruction of airflow through the burners. The flame should be blue with straight yellow tops. If excessive yellow 

flame is detected, turn off heater and consult “Troubleshooting” on page 13. 

 
Re-Lighting

Note

: For your safety, control knob cannot be turned OFF without first depressing the control knob and then 

rotating to OFF. 

1. Turn control knob to OFF. 
2. Wait at least 5 minutes to allow gas to dissipate before re-lighting. 

3. Repeat the “Lighting” steps listed on page 10. 

 

 
 

 

 

 

Shut Down

1. Turn control knob clockwise to OFF while depressing the knob. 
(Normally, burner will make a slight popping noise when extinguished). 

2. Turn cylinder valve clockwise to OFF and disconnect regulator when heater is not in use. 

NOTE

: After use, some discoloration of the emitter screen is normal. 

 
Operation Checklist

For a safe and pleasurable heating experience, perform this check before each use: 

Before Operating

1. I am familiar with entire owner’s manual and understand all precautions noted. 

2. All components are properly assembled, intact and operable. 
3. No alterations have been made. 

4. All gas connections are secure and do not leak. 
5. Wind velocity is below 10 mph. 

6. Unit will operate at reduced efficiency below 40 degrees F. 
7. Heater is for use outdoors (outside any enclosure). 
8. There is adequate fresh air ventilation. 

9. Heater is away from gasoline or other flammable liquids or vapors. 
10. Heater is away from windows, air intake openings, sprinklers and other water sources. 

11. Heater is at least 36 in. on top and at least 24 in. on sides from combustible materials. 
12. Heater is on a hard and level surface. 

13. There are no signs of spider or insect nests in heater orifices. 
14. All burner passages are clear. 

15. All air circulation passages are clear. 
16. Children and adults should be alerted to the hazards of high surface temperatures and should stay away to 
avoid burns or clothing ignition. 

17. Young children should be carefully supervised when they are in the area of the heater. 
18. Clothing or other protective material should not be hung from the heater, or placed on or near the heater. 

19. Any guard or other protective device removed for servicing the heater must be replaced prior to operating 
the heater. 

20. Installation and repair should be done by a qualified service person. The heater should be inspected before 
each use and at least annually by a qualified service person. 

21. More frequent cleaning may be required as necessary. It is imperative that control compartment burner and 

OPERATING INSTRUCTIONS

Содержание 61176















Отзывы: