Welker AD905BP Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 47

background image

31

IOM-189

MODEL: INFLOW™ ACE MANUAL INSERTION

REV: G

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

Maintaining the Insertion Tool

Figure 17: Insertion Tool Housing Cap Diagram

10.

Disconnect the insertion tubing from the insertion tool housing cap.

11.

Unscrew the insertion tool housing cap from the insertion tool housing.

12.

Carefully pull the insertion tool shaft from the insertion tool housing.

13.

Carefully pull the insertion tool shaft through the insertion tool housing cap.

14.

Replace the O-rings and back ups in the insertion tool housing cap and on the insertion tool shaft piston.

15.

Inspect the wiper ring, retaining ring, and bearing in the insertion tool housing cap and on the insertion tool shaft piston
for signs of damage or wear. Replace as necessary.

16.

Inspect the insertion tool housing for scratches. All cylinder bores should be clean. If scratches are present, polish the
insertion tool housing.

17.

Inspect the insertion tool shaft for scratches. If scratches are present, polish the insertion tool shaft.

18.

Wrap the exposed threads at the top of the insertion tool shaft with PTFE tape, and then lightly lubricate the outer
diameter of the insertion tool shaft.

19.

Wrap the exposed threads at the top of the insertion tool housing with PTFE tape.

20.

Carefully push the insertion tool shaft through the insertion tool housing cap, and then install the insertion tool housing
cap to the insertion tool housing.

21.

Tighten the insertion tool housing cap.

22.

To maintain the second insertion tool assembly, repeat steps 10–21.

23.

Once both insertion tool assemblies have been maintained and reassembled, continue to step 24.

«
...
29
30
31
32
33
...
»

Содержание AD905BP
















































Отзывы:

Нет отзывов

Похожие инструкции для AD905BP

DigitalFlow XMT868i

Бренд: Panametrics Страницы: 74

Бренд: E Instruments Страницы: 2

Бренд: Hach Страницы: 38

Бренд: Hach Страницы: 28

Бренд: Hach Страницы: 40

POCKET COLORIMETER II

Бренд: Hach Страницы: 142

Бренд: Hach Страницы: 4

Бренд: Hach Страницы: 308

Бренд: Hach Страницы: 158

Бренд: Hach Страницы: 118

POCKET COLORIMETER II

Бренд: Hach Страницы: 116

Бренд: Hach Страницы: 132

Бренд: Hach Страницы: 8

Бренд: Hach Страницы: 38

Бренд: Hach Страницы: 200

Бренд: Yamaha Страницы: 8

Бренд: Schneeberger Страницы: 35

Vortex Flow Industry

Бренд: Grundfos Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды