background image

DANGER

Please observe the following rules to avoid serious accidents

  Never use the equipment for purposes other than welding.

  Follow related regulations regarding the characteristics of the power source, choice of place, usage of high-

 

  

pressure gas, storage, configuration, safe-keeping of the workpiece after welding and disposal of waste, etc.

  Non-essential personnel shall not enter the welding area.

  Persons using pacemaker are not allowed near the welding machine or welding area without doctor's 

  

permission. The magnetism created by energizing the welding machine may have a negative effect on the 

  

pacemaker.

  The installation, operation, inspection and maintenance of the equipment must be carried out by authorized 

  

personnel.

  For your safety, you must understand the contents of the user’s manual.

DANGER

Please observe the following rules to avoid electric shock

  Keep away from any electrical parts.

  The machine and workpiece shall be grounded by authorized personnel.

  Cut off the power before installation or inspection, and restart it 5 minutes after finishing that activity. The 

  

capacitor is a rechargeable device. Please ensure it has no voltage before starting again even if the power

  

source is cut off.

 

Never use wire with inadequate wire gauge, damaged insulation sleeve or exposed conductor.

  Do ensure the proper isolation of wire connections.

  Never use the device when the enclosure is removed.

  Never use broken or wet insulation gloves.

  Welding screens must be used when working in overhead position.

  Check and maintain the equipment regularly. Do not use the equipment until the faulty parts are fixed.

  Turn off the power when not in use.

  Follow the related national and local standards and regulations when using the AC welding machine in 

  

confined spaces or overhead position.

DANGER

Please observe the following instructions to avoid fire, explosions, etc.

  Remove combustible materials from the welding area.

  Keep away from any combustible materials while welding.

  After welding, keep the hot workpiece away from flammable gases.

  Remove all combustible materials when welding in a patio, on the ground or on a wall.

  The work lead of the base metal should be as close to the welding place as possible.

  Never weld installations with gas pipes or airtight valves.

  Keep a fire extinguisher close to the welding area to prevent fire.

5

Содержание TIGACDC200GD

























Отзывы: