background image

0DFK

$LU$EUDVLRQ6\VWHP

8VHU·V*XLGH

&RQWHQWV

1.

Safety..................................................................... 2

2.

Contra-Indications and   Indications ...................... 3

3.

System Overview ................................................... 3

4.

System Unpacking, Setup, and Check-out ............ 4
Filling the Powder Chamber .................................. 4
User Settings ......................................................... 4

5.

Using the System................................................... 5
Unit Shutdown........................................................ 5

6.

Mach 8 Special Instructions................................... 5

7.

Routine Maintenance ............................................. 6

8.

Troubleshooting ..................................................... 8

9.

Warranty, Returns and Adjustments...................... 9
Returns and Adjustments ...................................... 9
Limited Warranty.................................................... 9
Storage and Shipment ........................................... 9

10. Specifications....................................................... 10
11. Recycling ............................................................. 10

CAUTION: This device must only be purchased by, or
sold to, a licensed dentist. Clinical use of the Mach 7/8
Air Abrasion system for procedures not included or
suggested in this guide is not advised. The Mach 7/8 Air
Abrasion system should only be used by dental
professionals who have practiced on extracted teeth and
are thoroughly familiar with the contents of this manual.

© 2000, Welch Allyn / Kreativ, Inc. All rights reserved. No part of

this manual may be reproduced without written permission
from Welch Allyn / Kreativ, Inc.

Kreativ Menu

Manuals

Содержание Kreativ











Отзывы: