Welbilt Convotherm OES mini easyTouch Скачать руководство пользователя страница 48

Страница: 48 / 106

5.4 Unpacking

Checking the tip indicator

Before unpacking the appliance, check the tip indicator on the packaging.
The following table shows the possible tip'n'tell indications:

Indicator

Meaning

Action

Silver dot:

Appliance has been transported cor‐

rectly.

■

Unpack the appliance.

■

Compare the number on the tip in‐

dicator with the accompanying pa‐

perwork.

Red dot:

Appliance has been turned over or

transported on its side.

■

Check the goods for damage.

■

Compare the number on the tip in‐

dicator with the accompanying pa‐

perwork.

■

Note down on the accompanying

paperwork the fact that the tip indi‐

cator has actuated and also any

damage.

Unpacking the appliance

Unpack the appliance as follows:

Step

Action

Illustration

Remove the outer packaging.

Remove all cardboard, packaging materials, custom‐

er documentation, labels and containers.

Please ensure that you dispose of packaging in an

environmentally friendly way.

Pull off the protective film.

Check the combi oven for damage. If you suspect

the appliance has been damaged during transit, noti‐

fy your dealer/carrier immediately. Please notify the

manufacturer in writing within three days.

Never install or put into service a damaged appli‐

ance under any circumstances.

5 Setting up the appliance

Installation manual

Содержание Convotherm OES mini easyTouch











































































































Результаты поиска

Содержание Convotherm OES mini easyTouch

Отзывы:

Похожие инструкции для Convotherm OES mini easyTouch

Бренды по названию

Популярные бренды

Welbilt Convotherm OES mini easyTouch, Руководство по установке

Результаты поиска

Содержание Convotherm OES mini easyTouch

Отзывы:

Похожие инструкции для Convotherm OES mini easyTouch

Бренды по названию

Популярные бренды