manualshive.com logo in svg

Weishaupt WTC-GB 15-B Compact, Инструкция по установке и эксплуатации

Weishaupt WTC-GB 15-B Compact - Компактный газовый котел с инструкцией по монтажу и эксплуатации. Можно скачать бесплатно на manualshive.com для получения руководства пользователя. Удобное решение для вашего дома.

Поделиться
Скачать
background image

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

6 Operation

83309302 1/2018-05 La

75-196

6.6.2.2 Boiler circuit

WTC-G ...

 

 

Boiler circuit

Parameters

Setting

2.2.1
Internal pump
operating mode HC

Operating mode of internal condensing unit pump for heating mode [ch. 12.4].

Load proportional
De-couple control
Proportional pressure stage 1 … 3
Constant pressure stage 1 … 3
Proport. pressure auto adaption
Constant pressure auto adaption

Factory setting depending on the selected hydraulic variant.

2.2.2
Internal pump
operating mode DHW

Operating mode of internal condensing unit pump for DHW mode [ch. 12.4].

Load proportional
Constant pump capacity

Factory setting depending on the selected hydraulic variant.

2.2.3
Pump capacity
minimum heating mode

Minimum pump capacity in heating mode.

2.2.4
Pump capacity
maximum heating mode

Maximum pump capacity in heating mode.

2.2.5
Pump capacity
minimal DHW mode

Minimum pump capacity for DHW loading.

2.2.6
Pump capacity
maximum DHW mode

Maximum pump capacity for DHW loading.

2.2.7
Minimum system pressure
warning

If the system pressure in the condensing unit drops below the value set, a warning
message is issued.

2.2.8
Minimum system pressure
burner lockout

If the system pressure in the condensing unit drops below the value set, an error
message is issued. The condensing unit is blocked. When the pressure rises
again, the appliance restarts automatically.

2.2.12
Inertia internal pump

Determines how fast the pump reacts to a change in the temperature differential
between flow/decouple.

The parameter is only effective, if parameter

 2.2.1 Internal pump oper-

ating mode HC 

is set to

 de-couple control

.

2.2.13
Pump capacity
boiler pump

Pump capacity of load pump stratified tank during DHW loading.

Only on compact version WAS … Power.

2.2.14
Inertia
DHW load pump

Depending on requirements, the pump capacity of the stratified storage tank load
pump is adjusted. The pump capacity changes by 1% each time the time set has
elapsed.

Содержание WTC-GB 15-B Compact





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WTC-GB 15-B Compact

K Tool International KTI63716 Owner'S Manual preview
KTI63716
Бренд: K Tool International Страницы: 20
Crivit 26301 Instruction Manual preview
26301
Бренд: Crivit Страницы: 23
QualityCraft MCVT120-150 Quick Start Manual preview
MCVT120-150
Бренд: QualityCraft Страницы: 10
Cozy Products COZY LEGS CL-R Instructions preview
COZY LEGS CL-R
Бренд: Cozy Products Страницы: 2
Salton SF13 Instructions And Warranty preview
SF13
Бренд: Salton Страницы: 7
vacuubrand MD 4C NT Instructions For Use Manual preview
MD 4C NT
Бренд: vacuubrand Страницы: 80
DAB E SYBOX MINI Assembly And Dismantling Manual preview
E SYBOX MINI
Бренд: DAB Страницы: 41
Detroit Radiant Products DSCS-10 Series Installation, Operation, Maintenance And Parts Manual preview
DSCS-10 Series
Бренд: Detroit Radiant Products Страницы: 32
Domus PROFAN-4 Installation Manual preview
PROFAN-4
Бренд: Domus Страницы: 2
Wacker Neuson PG2A Operator'S Manual preview
PG2A
Бренд: Wacker Neuson Страницы: 60
Daikin Altherma 3 H W Installation Manual preview
Altherma 3 H W
Бренд: Daikin Страницы: 32
fluid-o-tech DGD PRO Series Instruction Manual preview
DGD PRO Series
Бренд: fluid-o-tech Страницы: 4
Enerco HEATSTAR HS22LP Operating Instructions And Owner'S Manual preview
HEATSTAR HS22LP
Бренд: Enerco Страницы: 48
Kambrook SNUGASABUG FAN HEATER KFH20 User Manual preview
SNUGASABUG FAN HEATER KFH20
Бренд: Kambrook Страницы: 4
Astralpool 32505 Technical Manual. Start-Up And Operation preview
32505
Бренд: Astralpool Страницы: 56
Heidolph ROTAVAC Instruction Manual preview
ROTAVAC
Бренд: Heidolph Страницы: 61
HJM RCL Original Operating Instructions preview
RCL
Бренд: HJM Страницы: 21
Lennox Elite XP16-024-230 Installation Instructions Manual preview
Elite XP16-024-230
Бренд: Lennox Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды