manualshive.com logo in svg

Weishaupt WTC-GB 15-B Compact, Инструкция по установке и эксплуатации

Weishaupt WTC-GB 15-B Compact - Компактный газовый котел с инструкцией по монтажу и эксплуатации. Можно скачать бесплатно на manualshive.com для получения руководства пользователя. Удобное решение для вашего дома.

Поделиться
Скачать
background image

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

5 Installation

83309302 1/2018-05 La

44-196

5.5 Condensate connection

DANGER

Danger of poisoning by escaping flue gas

Flue gas can escape if the siphon is not filled. Inhalation leads to dizziness, nausea
and eventually death.

Check the fill level of the siphon at regular intervals and replenish if necessary, in
particular when the system has been shut down for longer periods or has been
operated at high return temperatures > 55 °C.

The condensate generated during the heating mode is discharged to the sewage
system via an integrated siphon.

Observe work sheet DWA-A 251 and local regulations, if required, fit a neutralisa-
tion system.

If the discharge point of the sewage system is above the condensate outlet:

Installing condensate lift pump.

Install condensate hose

Place condensate hose in such a way that it is not possible for a water bag to form
(siphon effect) and the condensate can drain away unimpeded.

Run condensate hose to condensate outlet pipe.

Filling the siphon

Fill the siphon with water via the flue gas outlet or inspection opening, until water
flows from the condensate hose.

CAUTION

Damage to boiler due to the accumulation of condensate

An accumulation of condensate can cause faults or damage the appliance.

If there is another siphon downstream of the appliance:

Install a connection piece with breather opening between the two siphons.

Содержание WTC-GB 15-B Compact





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WTC-GB 15-B Compact

Panasonic WH-MDC05F3E5 Operating Instructions Manual preview
WH-MDC05F3E5
Бренд: Panasonic Страницы: 100
Panasonic WH-SDC07H3E5 Quick Manual preview
WH-SDC07H3E5
Бренд: Panasonic Страницы: 88
Panasonic Aquarea WH-MDF09C3E5 Installation Manual preview
Aquarea WH-MDF09C3E5
Бренд: Panasonic Страницы: 90
Panasonic WH-MDC05J3E5 Operating Instructions Manual preview
WH-MDC05J3E5
Бренд: Panasonic Страницы: 80
Saci SIGMA Installation And Maintenance Manual preview
SIGMA
Бренд: Saci Страницы: 24
Calpeda MGP Original Operating Instructions preview
MGP
Бренд: Calpeda Страницы: 4
vacuubrand ME 2 Instructions For Use Manual preview
ME 2
Бренд: vacuubrand Страницы: 24
Lasko 754200 Operating Manual preview
754200
Бренд: Lasko Страницы: 4
Larius TORNADO 2 Series Operating And Operating And Maintenance Instructions preview
TORNADO 2 Series
Бренд: Larius Страницы: 32
Vaillant VWZ MPS 40 System Installation Instructions preview
VWZ MPS 40
Бренд: Vaillant Страницы: 80
L.B. White 346 Owner'S Manual And Instructions preview
346
Бренд: L.B. White Страницы: 18
DAB KC Series Instruction For Installation And Maintenance preview
KC Series
Бренд: DAB Страницы: 64
Wacker Neuson PT 6L Operator'S Manual preview
PT 6L
Бренд: Wacker Neuson Страницы: 72
Bestway Alwayzaire P3062 Owner'S Manual preview
Alwayzaire P3062
Бренд: Bestway Страницы: 2
Graco HYDRA-SPRAY President A Series Instructions-Parts List Manual preview
HYDRA-SPRAY President A Series
Бренд: Graco Страницы: 20
Zibro SRE 172 E Operating Manual preview
SRE 172 E
Бренд: Zibro Страницы: 14
T.I.P. Garten Jet 750 Operating Instructions Manual preview
Garten Jet 750
Бренд: T.I.P. Страницы: 133
Noctua NF-B9 PWM User Manual preview
NF-B9 PWM
Бренд: Noctua Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды