manualshive.com logo in svg

Weishaupt WTC-GB 15-B Compact, Инструкция по установке и эксплуатации

Weishaupt WTC-GB 15-B Compact - Компактный газовый котел с инструкцией по монтажу и эксплуатации. Можно скачать бесплатно на manualshive.com для получения руководства пользователя. Удобное решение для вашего дома.

Поделиться
Скачать
background image

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

9 Servicing

83309302 1/2018-05 La

128-196

9.2.4 Removing and refitting magnesium anode

Observe notes on servicing [ch. 9.2.1].

Corrosion protection requires an anode current greater than 1 mA with a minimum
water conductivity of 100 µS/cm (25 °C).

Measure anode current.

If the anode current is below 1 mA with the stipulated minimum conductivity, the
magnesium anode must be removed and tested.

Removing

Remove inspection flange [ch. 9.2.3].

If the diameter over half the anode length less than 15 mm:

Replace magnesium anode.

A shorter maintenance interval is required, if wear of the magnesium anode is no-
ticeably rapid.

Refitting

Refit magnesium anode in in reverse order, and:

fit new seals 

2

 and ensure sealing surfaces are clean,

connect anode cable 

1

,

tighten screws with a torque of 8 Nm.

Fit inspection flange [ch. 9.2.3].

CAUTION

Corrosion due to missing anode cable

If the electrical connection of the anode to the steel wall is missing, no protective
layer is formed. A missing protective layer can lead to corrosions.

Connect anode cable.
Anode is connected to fresh water storage tank.

1

2

Check anode current (greater than 1 mA), enter value and date on label.
Enter completed service on label.

Содержание WTC-GB 15-B Compact





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WTC-GB 15-B Compact

NARVI 30 Series Installation, User And Maintenance Instructions preview
30 Series
Бренд: NARVI Страницы: 12
Salamander Pumps EVE Installation And Warranty Manual preview
EVE
Бренд: Salamander Pumps Страницы: 24
Jaga Knockonwood DBE KNUF Assembling Instructions preview
Knockonwood DBE KNUF
Бренд: Jaga Страницы: 4
Jaga Micro Canal Mounting Instructions preview
Micro Canal
Бренд: Jaga Страницы: 8
Jaga BRIZA 041 Installation Instructions Manual preview
BRIZA 041
Бренд: Jaga Страницы: 12
Watershed Innovations HydraPump Smart Instructional Manual preview
HydraPump Smart
Бренд: Watershed Innovations Страницы: 11
Aspen Pumps mini aqua pump Installation & Maintenance Manual preview
mini aqua pump
Бренд: Aspen Pumps Страницы: 13
Modine Manufacturing GEO16-501.4 Installation And Service Manual preview
GEO16-501.4
Бренд: Modine Manufacturing Страницы: 28
usha FH 3114 S Instruction Manual preview
FH 3114 S
Бренд: usha Страницы: 8
TradeQuip 2054T Owner'S Manual preview
2054T
Бренд: TradeQuip Страницы: 8
Jandy Pro Series JXi R0591900 Installation Instructions preview
JXi R0591900
Бренд: Jandy Pro Series Страницы: 4
Becker O 5.4 Operating Instructions preview
O 5.4
Бренд: Becker Страницы: 5
Vectra Fitness FM-1309-Z User Manual preview
FM-1309-Z
Бренд: Vectra Fitness Страницы: 28
Salvador Escoda LXDY3 Instruction Manual preview
LXDY3
Бренд: Salvador Escoda Страницы: 10
C.P.A. 1041030 User Manual preview
1041030
Бренд: C.P.A. Страницы: 40
Utilitech 0955549 Manual preview
0955549
Бренд: Utilitech Страницы: 40
Source Network Life Smart Zone LCHT10955US Manual preview
Life Smart Zone LCHT10955US
Бренд: Source Network Страницы: 16
Macnaught BOP20 Instruction Manual preview
BOP20
Бренд: Macnaught Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды