Weishaupt WTC-GB 15-B Compact Скачать руководство пользователя страница 126 | Manualshive

Страница: 126 / 196

Weishaupt WTC-GB 15-B Compact Скачать руководство пользователя страница 126

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

9 Servicing

83309302 1/2018-05 La

126-196

9.2 Fresh water storage service

9.2.1 Notes on servicing

Servicing must only be carried out by qualified personnel. The system should be
serviced annually.

Weishaupt recommends a service contract is entered into to ensure regular in-
spections.

Prior to every servicing

Inform the operator about the extent of service work to be carried out.
Switch off installation and safeguard against accidental re-start.
Close fresh water inlet.
If necessary, remove fresh water storage tank.

Following servicing

Open fresh water inlet.
If necessary fill with water and vent.
Carry out soundness test.
Check anode current (greater than 1 mA), enter value and date on label.
Carry out a function test.

9.2.2 Service plan

Components

Criteria

Service procedure

Fresh water storage

Calcification

Clean

Magnesium anode

Anode current less than 1 mA

Check the insulated mounting of the
anode (minimum resistance 100 kΩ).
Check or request minimum conductiv-
ity of the water [ch. 9.2.4].
Check diameter.
Check condition of enamel.

If the anode current is still less than
1 mA, this may, in exceptional cases, be
due to an above-average enamel finish.

Wear

Check diameter (every 2 years).

Diameter over half the anode length less
than 15 mm

Replace

Externally powered anode (op-
tional)

Control lamp red or off

Check function.
Check the insulated mounting of the
anode (minimum resistance 100 kΩ).
Replace

Anode current less than 1 mA

Check function, if necessary restore.
Check the insulated mounting of the
anode (minimum resistance 100 kΩ).
Check or request minimum conductiv-
ity of the water [ch. 11.1].
Check condition of enamel.

If the anode current is still less than
1 mA, this may, in exceptional cases, be
due to an above-average enamel finish.

Lagging

Damage

Replace

«
...
124
125
126
127
128
...
»

Содержание WTC-GB 15-B Compact





































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды