Weishaupt WHI freshaqua 22 #1 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 32

Weishaupt WHI freshaqua 22 #1 Скачать руководство пользователя страница 8

Installation and operating instructions

Fresh water station WHI freshaqua 22

3 Product description

83514302 ▪ 1/2017-08 ▪ Ext. PAW

8-32

3.1

Function

The fresh water stations WHI freshaqua are used for the comfortable and hygienic

heating of domestic water according to the continuous flow heater principle. Other than

in conventional domestic water storage tanks, the foodstuff water is not used for energy

storage and stored as hot water for hours or days. It is only heated when required using

a high-performance plate heat exchanger. The energy for heating the domestic water

comes from a buffer tank that can be heated by different systems - by solar systems as

well as by solid fuel boilers, oil / gas boilers, heat pumps or other systems.
The WHI freshaqua modules are well suited for use in combination with a thermal solar

system. The very good cooling of the heating water in the highly effective plate heat

exchangers leads to an increased efficiency of the solar circuit as the average

temperature of the solar circuit can be reduced due to the cold return.
In the event of great tapping differences, the WHI freshaqua fresh water stations always

have to guarantee a constant outlet temperature at the hot water tap.

The speed of the highly efficient EC pumps of the latest generation is controlled by a

high-performance closed-loop control always allowing the heating flow rate to be optimal-

ly set to the current tap capacity.
The closed-loop control receives the necessary information for adjusting the system from

a flow rate sensor and extremely fast temperature sensors that detect the smallest

temperature deviations immediately.
The WHI freshaqua can also be equipped with a highly efficient EC circulation pump as

an option. The closed-loop control can operate the pump in different circulation modes;

always adapted to the current system and requirements of the customer.
During commissioning, the circulation return temperature can be set individually on the

circulation system so that the recordable and traceable DVGW (551) requirements for a

maximum cooling of the circulation by 5 K can be fulfilled.
Thus, the WHI freshaqua offer perfect comfort, optimum hygiene and a future-orientated

energy saving operation.

3.2

Serial number

The serial number on the type plate clearly identifies each product. The serial number is

necessary for the Weishaupt after-sales service. In case of a complaint, please send us

the serial number of the product concerned and the completed commissioning report

(see page 31). The serial number is placed in the upper right corner of the support sheet

of the station.

Serial number:

«
...
6
7
8
9
10
...
»

Содержание WHI freshaqua 22 #1

































Отзывы:

Нет отзывов