Z-Wave System Notes
This product is a security enabled Z-wave Plus product and must be used with a Security
Enabled Z-Wave controller to be fully utilized. Z-Wave is a “Wireless mesh network,” and
results may vary based on building construction and communication path.
To assure interoperability, each Z-Wave product must pass a stringent conformance test to
assure that it meets the Z-Wave standard for complete compliance with all other devices and
controls. The Z-Wave identity mark assures consumers, integrators, dealers and manufacturers
that their products will reliably perform with any other Z-Wave device. And, regardless of the
vendor, always powered nodes may act as a repeater for Kwikset/Weiser/Baldwin products.
Z-Wave Configuration and Association Parameters are available on
the SmartCode 5 Lever page at www.kwikset.com.
Removing the lock from the network
Follow your smart home system’s instructions
to remove the lock from the network. When
prompted by the system, press button A” on the
lock interior once.
© 2016 Spectrum Brands, Inc.
1.
Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution statements.
3. Remind all family members of safety precautions.
4. Protect your user codes and mastercode.
5. Dispose of used batteries according to local laws and regulations.
CAUTION:
Prevent unauthorized entry. Since anyone with access to the back panel
can change the user codes, you must restrict access to the back panel and routinely
check the user codes to ensure they have not been altered without your knowledge.
The use of a mastercode can help protect your system’s settings.
WARNING:
This Manufacturer advises that no lock can provide complete security
by itself. This lock may be defeated by forcible or technical means, or evaded by
entry elsewhere on the property. No lock can substitute for caution, awareness of
your environment, and common sense. Builder’s hardware is available in multiple
performance grades to suit the application. In order to enhance security and reduce
risk, you should consult a qualified locksmith or other security professional.
Important Safeguards
Alert
Reason
Solution
Keypad flashes red 1 time
with 1 beep*
Door jammed while
attempting to lock.
Manually re-lock door. If needed,
reposition strike.
Keypad flashes red 3 times
with 3 beeps*
Unsuccessful programming.
Attempt programming procedure
again.
One incorrect code entered.
Re-enter code.
No user code programmed.
Program at least one user code.
Keypad flashes red 10
times with 10 beeps*
Low battery.
Replace batteries.
Lock beeps 2 times.
Programming timeout.
Attempt programming procedure
again, making sure not to pause for
more than 5 seconds.
Keypad flashes red 3 times.
Keypad flashes red 6 times
with 6 beeps*.
Keypad flashes red 15 times
with 15 beeps*
Three incorrect codes entered
within one minute.
Re-enter code after 60-second keypad
lockout.
*Beeping sound will only be heard if switch #3 is on.
Network Information
4 / 4
SmartCode at a Glance
Deleting a User Code
In order to delete a user code, you must override the code by adding a different user code in the same
position. For example, if you want to delete the third code, add a different user code in position three.
Test the old user code to make sure it can no longer unlock the door.
If you cannot remember the user code position, you may wish to perform a factory reset to delete all
codes associated with the lock.
Reference Guide
Exterior
Back
panel
Program
button
Status
LED
Switches
Turnpiece
Interior (cover removed)
Switches and Status LED Colours
Troubleshooting
Switch
Function
1
Door lock status LED blinks every 6
seconds
2
Lock automatically re-locks door 30
seconds after unlocking. Disabled if no
codes are programmed.
3
Audio
4
Not used.
Colour
Lock Status
Green
Unlocked
Amber
Locked
Red
Low battery
1 2 3 4
On
Switches
Status
LED
Off
System Alerts
Factory Reset
Battery Replacement
A factory reset will delete all codes associated with the lock,
and it will remove it from your smart home system.
If another lock is installed above the lever, remove the interior
assembly when battery replacement is required.
Status
LED
1 Remove
battery pack.
2 Press and HOLD the Program
button while reinserting
the battery pack.
Keep holding the button for 30
seconds until the lock beeps
and the status LED flashes red.
Keypad
Lock
button
Keyway
SmartKey
tool hole
Button “A”
Button “B”
3 Press the Program button
once more. When the LED
flashes green and you
hear one beep, the lock
has been reset.
4 Pair the lock with your smart home
system, and add user codes to your lock.
A complete Programming and Troubleshooting Guide is available on
the SmartCode 5 Lever page at www.weiserlock.com.
Lock
above
lever
Mounting
plate
Interior
assembly
Battery
pack
