background image

2

 

Particular note should be taken to the position of variable speed drives and switching power supplies. 

Their input and load cables should be screened to a central star earth point. 

 
 

2.1.2 Making a NEMA-4 Mounting 

Panel   
Details
 

The unit can be mounted into panels with a depth of 4”(105mm).    It is recommended that 
the unit be mounted on the front panel of a steel enclosure, through an appropriate opening*. 
Allow a clearance of 1”(25mm) around the sides of the unit for mounting hardware. Allow 
clearance for cable connections to the back of the unit. Unit depth may vary according to 
cable type used. Typically, plan a depth to accommodate at least 4”(105mm) behind the 
panel. 

NEMA-4 
Mounting
 

Put the unit through the panel cut out. Slide the clamps into the 6~8 holes provided around 
the case. Tighten the clamping screws in an even pattern until the unit is secured in the 
panel. 

Caution! 

Do not over tighten mounting clamps! 

Note: 

Specifications 

Note: To seal to NEMA-4 specifications, all supplied mounting clamps must be used and 
panel cannot flex more than 0.010”. 

2.1.3 Environmental Considerations 

 

 

The NP-700p are to be used indoors as built in displays. Make sure that the displays are 
installed correctly and that the operating limits are followed (See Specifications). 

 

Do not operate the unit in areas subject to explosion hazards due to flammable gases, 
vapors or dusts. 

 

The unit should not be installed where fast temperature variations and/or high humidity 
are present. This will cause condensation of water in the device. 

 

Do not install these terminals in environments where have inflammable gases. 

 

2.2 Power Connections 

Make sure that all local and national electrical standards are met when the installing the unit. Contact 
your local authorities to determine which codes apply. 

2.2.1 Power Requirements 

 

 

Power 

The NP-700p can be powered by DC power only. The specified voltage 
range is 

24±20%

 Volts DC. This insures compatibility with most controller 

DC systems.   
The power conditioning circuitry inside the unit is accomplished by a 
switching power supply. The peak starting current can be as high as 700mA. 

 

Fusing 
Requirements
 

If the display does not come on within 2 seconds of power up, remove 
power. An internal fuse will prevent damage if the polarity of the DC power 
is incorrect. Check wiring to insure proper connections and try to power up 
again. 

 

Caution 
High Voltage

 

An Internal fuse will prevent damage for over voltage condition however it 
isn’t guaranteed. 
DC voltage sources should provide proper isolation from main AC power 
and similar hazards. 

 

Caution 
Emergency 
Stop
 

A Hard-wired EMERGENCY STOP should be fitted in any system using an 
NP-700p to comply with ICS Safety Recommendations. 

 

Содержание NP-700p Series










Отзывы: