4
5
6
V1.0 / 2020-10-29
Warning / Avertissement
Take into consideration the following guidelines before wiring the device
o
Tenez compte des directrices suivantes avant de câbler l’appareil.
Terminal block is mating with Plug and suitable for 12-24AWG. Torque
value 4.5 lb-in.
o
Le bornier est compatible avec les connecteurs et convient pour 12-
24AWG. Valeur de couple 4,5 lb-in.
The temperature rating of the input connection cable should higher than
105°C.
o
La température de service nominale du câble d’entrée doit être
supérieure à 105 °C.
Supplied by SELV source evaluated by UL 61010-1 or 61010-2-201
power supply only.
o
Fourni par la source SELV évaluée uniquement par l'alimentation UL
61010-1 or 61010-2-201.
Note about behavior of power failure relay:
Relay contact is closed if the device is powered-off.
Relay contact is open if the device is powered by PWR1
and
PWR2
Relay contact is closed if device is powered
either
by PWR1
or
PWR2
9. Communication Connections
Switch
IE-SW-EL18-16TX-2GC
is equipped with following communication interfaces:
16x
10/100Base-T(X) ports
2x
Ethernet-Combo-Ports, that can be used either as 10/100/1000Base-T ports or
alternatively as 1000Base-X ports with respective SFP Transceivers (mini-GBIC)
Please only use cables suitable for the respective type of communication and ensure that
signals are protected from possible interference.
9.1
10/100Base T(X) RJ45 Ports
The 10/100BaseT(X) ports located on Ethernet Switch’s front panel are used to connect
to Ethernet-enabled devices. Below we show pinouts for both MDI (NIC-type) ports and
MDI-X (HUB/Switch-type) ports. Auto MDI-X ensures that both wiring-schemes are
supported (Automatic crossover function).
10/100Base T(X) RJ45 Pinouts
MDI Port Pinouts
MDI-X Port Pinouts
8-pin RJ45
Pin
Signal
Pin
Signal
1
Tx+
1
Rx+
2
Tx-
2
Rx-
3
Rx+
3
Tx+
6
Rx-
6
Tx-
9.2
1000Base Combo-Ports
The switch is equipped with 1000Base combo ports that can be used either as 10/100/
1000Base-T ports with RJ45 connector or with optional SFP transceivers (mini GBIC) for
1000 Base-X (e.g. for connections with fiber optic technology over long distances). For
correct function, please note that only one function of a combo port may be used and
connected at a time. The RJ45 port can only be used if no SFP module is plugged. in.
9.2.1
1000BaseT Ethernet Port Connection
1000BaseT data is transmitted on differential TRD+/- signal pairs over copper wires.
Pin
Signal
1
TRD(0)+
2
TRD(0)-
3
TRD(1)+
4
TRD(2)+
5
TRD(2)-
6
TRD(1)-
7
TRD(3)+
8
TRD(3)-
9.2.2
1000Base-X SFP (mini-GBIC) Fiber Port
The 1000Base-X type slots, require 1000Base-X SFP (mini-GBIC) fiber transceivers to
work properly. Weidmüller provides transceiver models for various distance requirements.
Please only use SFP modules and cables that are compatible with each other to establish
an optical connection.
LC-Port with separate Transmit and Receive Port:
Remember to connect the Tx (transmit) port of Device-1 to the Rx (receive) port of Device-
2I, and the Rx (receive) port of Device-1 to the Tx (transmit) port of Device-2.
LC-Port Pinouts
LC-Port to LC-Port Cable Wiring
10. LED Indicators
The front panel of the Ethernet Switch contains several LED indicators. The function of
each LED is described in the table below.
LED
Color
Status
Description
PWR1
Green
On
Power is supplied to power input PWR1.
Off
Power is not supplied to power input PWR1.
PWR2
Green
On
Power is supplied to power input PWR2.
Off
Power is not supplied to power input PWR2.
LNK/ACT
(Ports 1- 16)
Green
On
Port’s link is active.
Off
Port’s link is inactive.
Blinking
Transmitting data.
Full/Half
Duplex
(Ports 1- 16)
Amber
On
Port is set to Full Duplex Mode.
Off
Port is set to Half Duplex Mode.
Blinking
Packet collisions detected.
LNK/ACT
(Combo Ports
G1/G2)
Green
On
RJ45-Link of Combo-Port is active.
Off
RJ45-Link of Combo-Port is inactive.
LNK/ACT
1000Base-X
(Combo Ports
G1/G2)
Green
On
Fiber-Link of Combo-Port is active.
Off
Fiber-Link of Combo-Port is inactive.
10/100/1000M
(Combo Ports
G1/G2)
Amber
On
Port speed of RJ45-Port is 100 Mbps.
Off
Port speed of RJ45-Port is either 10 or 1000
Mbps (1000 Mbps supports only Full Duplex).
11. Specifications
Technology
Standards
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-TX
IEEE 802.3z for 1000Base-X
IEEE 802.3ab for 1000Base-T
IEEE 802.3x for Flow Control
Processing Type
Store and Forward
MAC Table size
8K
Packet buffer size
1 Mbit
Backplane bandwidth
7.2 Gbps
Interfaces
RJ45 Ports
10/100BaseT(X) auto negotiation speed, F/H duplex mode
and auto MDI/MDI-X connection
SFP / RJ45 1000Base
Combo-Port
10/100/1000Base-T auto negotiation speed, F/H duplex
mode and auto MDI/MDI-X connection or 1000Base-X
LED Indicators
PWR1, PWR2 (Power)
SFP/RJ45 Combo-Port Link/Activity
RJ45: Port Link/Activity, Port Speed
Relay Contact
Max. 1A @ 24 VDC
Power
Input Voltage
24 V DC (12 - 48 V DC), 2 redundant inputs
Input Current @24 VDC
0.35 A
Connection
One removable 6-pin terminal block, Wiring cable 12-24AWG
Overload Current
Protection
Present
Reverse Polarity
Protection
Present
Physical Characteristics
Housing
IP30 protection, metal
Dimension (W x H x D)
96.4 x 154 x 108.5 mm (3.8 x 6.06 x 4.27 in)
Weight
1235 g
Installation
DIN-rail
Environmental conditions
Operating Temperature
-40 to 75°C (-40 to 167°F)
Storage Temperature
-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity 5 to 95% (non-condensing)
Altitude
up to 2000 m
Regulatory Approvals
Safety
UL 61010-1; UL 61010-2-201
EMC
EN 55032, EN 55024, FCC Part 15 Subpart B Class A
IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV,
IEC 61000-4-3 RS: 80 MHz to 1 Ghz: 3 V/m,
IEC 61000-4-4 EFT: Power: 0.5 kV; Signal: 0.5 kV,
IEC 61000-4-5 Surge: Power: 0.5 kV; Signal: 1 kV,
IEC 61000-4-6 CS: 3 Vrms
Shock
IEC 60068-2-27
Free Fall
IEC 60068-2-31
Vibration
IEC 60068-2-6
MTBF
Time
748.087 hrs
Database
Telcordia SR332
Warranty
Time Period
5 years
Contact Information
Weidmüller Interface GmbH & Co. KG
Klingenbergstraße 26, 32758 Detmold / Germany
Phone +49 (0) 5231 14-0, Fax +49 (0) 5231 14-292083
, Internet
www.weidmueller.com
