4
5
6 Edition 6 / 2020-07
8. Wiring Redundant Power Inputs and Power Fault
Relay
The switch supports redundant power supply inputs and provides a power fault relay
which can be used for alarming in case of interruption of Power 1 or Power 2 on the 6-
pin terminal block. Refer to illustration below for correct wiring.
Warning / Avertissement
Take into consideration the following guidelines before wiring the device
o
Tenez compte des directrices suivantes avant de câbler l’appareil.
Terminal block is mating with Plug and suitable for 12-24AWG. Torque
value 4.5 lb-in.
o
Le bornier est compatible avec les connecteurs et convient pour 12-
24AWG. Valeur de couple 4,5 lb-in.
The temperature rating of the input connection cable should higher than
105°C.
o
La température de service nominale du câble d’entrée doit être
supérieure à 105 °C.
Supplied by SELV source evaluated by UL 61010-1 or 61010-2-201
power supply only.
o
Fourni par la source SELV évaluée uniquement par l'alimentation UL
61010-1 or 61010-2-201.
Note about behavior of power failure relay:
Relay contact is closed if the device is powered-off.
Relay contact always is open if the device is powered either by PWR1 or PWR2 and if
DIP switches 1 and 2 for power control are set to off.
Relay contact closes if DIP switch 1 is set to ON and PWR1 fails.
Relay contact closes if DIP switch 2 is set to ON and PWR2 fails.
9. Communication Connections
Switch
IE-SW-EL08-8GT
is equipped with:
8x
10/100/1000Base-T(X) Ethernet ports (Auto MDI-X)
Switch
IE-SW-EL05-4GT-1GESFP
is equipped with:
4x
10/100/1000Base-T(X) Ethernet ports (Auto MDI-X)
1x
1000Base-X slot to be used with SFP Transceivers (mini-GBIC) [accessories]
Please only use cables suitable for the respective type of communication and ensure
that signals are protected from possible interference.
9.1
10/100/1000Base T(X) RJ45 Ports
The 10/100BaseT(X) ports located on Ethernet Switch’s front panel are used to
connect to Ethernet-enabled devices. Below we show pinouts for both MDI (NIC-type)
ports and MDI-X (HUB/Switch-type) ports. Auto MDI-X ensures that both wiring-
schemes are supported (Automatic crossover function).
Pinouts 10/100/1000Base T(X) RJ45
8-Pin RJ45
Port
10/100 Base-T(X) MDI/MDI-X
1000Base-T MDI/MDI-X
Pin No.
MDI port
MDI-X port
Pin No.
MDI port
MDI-X port
1
TD+(transmit)
RD+(receive)
1
BI_DA+
BI_DB+
2
TD-(transmit)
RD-(receive)
2
BI_DA-
BI_DB-
3
RD+(receive)
TD+(transmit)
3
BI_DB+
BI_DA+
4
Not used
Not used
4
BI_DC+
BI_DD+
5
Not used
Not used
5
BI_DC-
BI_DD-
6
RD-(receive)
TD-(transmit)
6
BI_DB-
BI_DA-
7
Not used
Not used
7
BI_DD+
BI_DC+
8
Not used
Not used
8
BI_DD-
BI_DC-
9.2
1000BaseSFP Port (only IE-SW-EL05-4GT-1GESFP)
The switch is equipped with an 1000BaseSFP slot that can be used with an optional
SFP transceivers (mini GBIC). Please only use SFP modules and cables that are
compatible with each other to establish an optical connection. Weidmüller provides
transceiver models for various distance requirements.
LC-Port with separate Transmit and Receive Port:
Remember to connect the Tx (transmit) port of device I to the Rx (receive) port of device
II, and the Rx (receive) port of device I to the Tx (transmit) port of device I
LC-Port Pinouts
LC-Port to LC-Port Cable Wiring
10. LED Indicators
The front panel of the Ethernet Switch contains several LED indicators. The function of
each LED is described in the table below.
LED
Color
Status
Description
PWR1
Green
On
Power is being supplied to power input PWR1.
Off
Power is not being supplied to power input PWR1.
PWR2
Green
On
Power is being supplied to power input PWR2.
Off
Power is not being supplied to power input PWR2.
FAULT
Amber
On
Indicates PWR1 or PWR2 fault (if
corresponding DIP switches are set to ON).
Off
If DIP switches are set to OFF or no power failure.
LNK/ACT (IE-
SW-EL08-8GT)
Green
/
Amber
Green
Port’s link is active at 1 Gbps.
Amber
Port’s link is active at 10/100 Mbps.
Off
Port’s link is inactive.
LNK/ACT (IE-
SW-EL05-4GT-
1GESFP)
Green
On
Port’s link is active.
Off
Port’s link is inactive.
Full/Half Duplex
(IE-SW-EL08-
8GT)
Amber
On
Port is set to Full Duplex Mode.
Off
Port is set to Half Duplex Mode.
Blinking
Packet collisions detected.
10/100/1000M
(IE-SW-EL05-
4GT-1GESFP)
Amber
On
Port speed is 100 Mbps.
Off
Port speed is 10 Mbps or 1 Gbps (Full Duplex).
LNK/ACT
1000Base-X
(IE-SW-EL05-
4GT-1GESFP)
Green
On
Fiber-Link is active.
Off
Fiber-Link is inactive.
11. Specifications
Technology
Standards
IEEE 802.3 for 10Base-T,
IEEE 802.3u for 100Base-TX
IEEE 802.3z for 1000Base-X
IEEE 802.3ab for 1000Base-T
IEEE 802.3x flow control
Processing Type
Store and Forward
MAC Table size
IE-SW-EL05-4GT-1GESFP: 1K; IE-SW-EL08-8GT: 4K
Packet buffer size
IE-SW-EL05-4GT-1GESFP: 1 Mbit
IE-SW-EL08-8GT: 1.5 Mbit
Backplane bandwidth
IE-SW-EL05-4GT-1GESFP: 10 Gbps
IE-SW-EL08-8GT: 16 Gbps
Jumbo frame support
IE-SW-EL05-4GT-1GESFP: up to 10 KB
IE-SW-EL08-8GT: 9216 Bytes
Interfaces
RJ45 Ports
10/100/1000BaseT(X) auto negotiation speed, F/H duplex
mode and auto MDI/MDI-X connection
SFP slot
1000Base-X
LED Indicators
PWR1, PWR2 (Power), Power Fault, Port Link/Activity,
Port Full/Half Duplex Mode
Relay Contact
Max. 1A @ 24 VDC
DIP Switches
Enabling/Disabling relay alarm for PWR1/PWR2 failure
Power
Input Voltage
24 V DC (12 - 48 V DC), 2 redundant inputs
Input Current @24 VDC IE-SW-EL05-4GT-1GESFP: 0.18 A; IE-SW-EL08-8GT: 0.2 A
Connection
One removable 6-pin terminal block, Wiring cable 12-24AWG
Overload Current
Protection
Present
Reverse Polarity
Protection
Present
Physical Characteristics
Housing
IP30 protection, metal
Dimension (W x H x D)
26.1 x 144.3 x 94.9 mm (1.03 x 5.68 x 3.74 in)
Weight
IE-SW-EL05-4GT-1GESFP: 403 g; IE-SW-EL08-8GT: 390 g
Installation
DIN-rail
Environmental conditions
Operating Temperature -40 to 75°C (-40 to 167°F)
Storage Temperature
-40 to 85°C (-40 to 185°F)
Ambient Relative
Humidity
5 to 95% (non-condensing)
Altitude
up to 2000 m
Regulatory Approvals
Safety
UL 61010-1, UL 61010-2-201
EMC
EN 55032, EN 55024, FCC Part 15 Subpart B Class A,
IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV,
IEC 61000-4-3 RS: 80 MHz to 1 Ghz: 3 V/m,
IEC 61000-4-4 EFT: Power: 0.5 kV; Signal: 0.5 kV,
IEC 61000-4-5 Surge: Power: 0.5 kV; Signal: 1 kV,
IEC 61000-4-6 CS: 3 Vrms
Shock
IEC 60068-2-27
Free Fall
IEC 60068-2-31
Vibration
IEC 60068-2-6
MTBF
Time
IE-SW-EL08-8GT: 926.332 hrs
IE-SW-EL05-4GT-1GESFP: 1.861.840 hrs
Database
Telcordia SR332
Warranty
Time Period
5 years
Contact Information
Weidmüller Interface GmbH & Co. KG
Klingenbergstraße 26, 32758 Detmold / Germany
Phone +49 (0) 5231 14-0, Fax +49 (0) 5231 14-292083
