Weidmuller IE-WL-BL-AP-CL Скачать руководство пользователя страница 11

Страница: 11 / 76

Wi-Fi device IE-WL-BL-AP-CL

Getting Started

2-11

LED

Color

State

Description

Front Panel LED Indicators (System)

PWR

Green

Power is being supplied from power input 1&2.

Off

Power is not being supplied from power input 1&2.

FAULT

Red

Blinking (fast at 0.5-sec intervals) Cannot get an IP address from the DHCP server

Blinking (slow at 1-sec intervals) IP address conflict

Off

Error condition does not exist.

STATE

Green/

Red

Green

Software Ready

Green/Blinking at 1-sec intervals The device has been located by the Search Utility.

Red

Booting error condition

SIGNAL

(5 LEDs)

Green

Signal level (for Client mode only)

Off

WLAN

Green

WLAN function is in Client mode and device has
established a link with an AP.

Blinking

WLAN data communication is run in Client mode

Off

WLAN is not in Client Mode or device has not
established a link with an AP.

Amber

WLAN function is in AP mode.

Blinking

WLAN’s data communication is run in

AP mode

Off

WLAN is not in use or not working properly

TP Port(RJ45) LED Indicators (Port Interface)

1000M

Green

TP port’s 10

00Mbps link is active.

Blinking

Data is being transmitted at 1000 Mbps

Off

TP port’s 10

00Mbps link is inactive.

10/100M

Amber

TP port’s 10

/100Mbps link is active.

Blinking

Data is being transmitted at 10/100 Mbps

Off

TP port’s

10/100Mbps link is inactive.

ATTENTION

When the system fails to boot, the LEDs for

STATE

(Green),

FAULT

, and

WLAN

will all light up

simultaneously and blink at one-second intervals. This might be due to improper operation or issues such as
an unexpected shutdown while updating the firmware. To instruction on recovering the firmware, refer to the

“Firmware Recovery” section in Chapter 6.

Beeper

The beeper emits two short beeps when the system is ready.

Reset Button

The

RESET

button is located on the rear panel of the device. You can

reboot the device or reset it to factory default settings by pressing the

RESET

button with a pointed object such as an unfolded paper clip.

•

System reboot:

Hold the RESET button down for under 5 seconds

and then release.

•

Reset to factory default:

Hold the RESET button down for

over

seconds until the

STATE

LED starts blinking green. Release the button

to reset the IE-WL-BL-AP-CL.

Содержание IE-WL-BL-AP-CL













































































Результаты поиска

Содержание IE-WL-BL-AP-CL

Отзывы:

Похожие инструкции для IE-WL-BL-AP-CL

Бренды по названию

Популярные бренды

Weidmuller IE-WL-BL-AP-CL, Руководство пользователя

Результаты поиска

Содержание IE-WL-BL-AP-CL

Отзывы:

Похожие инструкции для IE-WL-BL-AP-CL

Бренды по названию

Популярные бренды