Weider 831.159530 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 35

Weider 831.159530 Скачать руководство пользователя страница 5

5

Make sure you have the following tools:

• Two adjustable wrenches

• One standard screwdriver

• One phillips screwdriver

• One rubber mallet

• You will also need grease or petroleum jelly, a

small amount of soapy water, and clear tape or
masking tape.

Note: Assembly will be more convenient if you have
a socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.

How to Identify Parts

To help you identify the small parts used in assembly,
we have included a PART IDENTIFICATION CHART
in the center of this manual. Place the chart on the
floor and use it to easily identify parts during each
assembly step.

Note: Some small parts may have

been pre-attached. If a part is not in the parts
bag, check to see if it has been pre-attached.

How to Orient Parts

As you assemble the weight system, make sure that
all parts are oriented exactly as shown in the draw-
ings.

Tightening Parts

Tighten all parts as you assemble them, unless
instructed to do otherwise.

Questions?

If you have questions after reading the assembly
instructions, please call our HELPLINE at

1-800-736-6879

.

Assembly Requires Two Persons

For your convenience and safety, assemble the
weight system with the help of another person.

Set Aside Enough Time

Due to the many features of the weight system, the
assembly process will take time. By setting aside
plenty of time and by deciding to make the task
enjoyable, assembly will go smoothly. You may want
to assemble the weight system over a couple of
evenings.

Select a Location for the Weight System

Because of its weight and size, the weight system
should be assembled in the location where it will be
used. Make sure that there is enough room to walk
around the weight system as you assemble it.

How to Unpack the Box

To make assembly as easy as possible, we have
divided the assembly process into four stages. The
parts needed for each stage are found in individual
bags.

Important: Wait until you begin each stage

to open the parts bag for that stage.

Place all

parts of the weight system in a cleared area and
remove the packing materials. Do not dispose of
the packing materials until assembly is completed.

Make Assembly Easier for Yourself

Everything in this manual is designed to
ensure that the weight system can be assem-
bled successfully by anyone.

Before begin-

ning assembly, make sure to read the
information on this page. This brief intro-
duction will save you much more time than
it takes to read it.

The Four Stages of the Assembly Process

Frame Assembly—

You will begin by assembling

the base and the uprights that form the skeleton of
the weight system.

Arm Assembly—

During this stage you will

assemble the arms and the leg lever.

Cable Assembly

—During this stage you will

attach the cables and pulleys that connect the
arms to the weights.

Seat Assembly—

During the final stage you will

assemble the seats and the backrests.

ASSEMBLY

«
...
3
4
5
6
7
...
»

Содержание 831.159530




































Отзывы:

Нет отзывов