05
GB
Fig.5
OPERATION
DRIVE CONTROL BAR-
used to engage power-pro-
pelled forward motion lawn mower.
THROTTLE CONTROL-
used for starting the engine
and allows you to select either fast or slow engine
speed.
STARTER HANDLE-
used for starting the engine.
MULCHER PLUG-
located at the discharge opening,
must be removed when converting to bagging operation.
(For 3in1 mower)
MULCHER DOOR-
allows conversion to discharge
or bagging operation.
(for 3in1/2in1 mower)
PRIMER-
pumps additional fuel from the carburetor
to the cylinder for use when starting a cold B&S engine.
OPERATOR PRESENCE CONTROL BAR-
must be
held down to the handle to start the engine. Release
to stop the engine.
GB
WARNING:
The operation of any lawn
mower can result in foreign objects thrown
into the eyes, which can result in severe
eye damage. Always wear safety glasses or eye
Shields while operating your lawn mower or per-
forming any adjustments or repairs. We recom-
mend wide vision safety mask over spectacles or
standard safety glasses.
HOW TO USE YOUR LAWN MOWER
ENGINE SPEED
A throttle located on the side of the upper handle
c o n t r o l s t h e e n g i n e s p e e d . F a s t p o s i t i o n i s f o r
normal cutting, trimming and better grass bagging.
Slow position is for light cutting, trimming and fuel
economy.
ENGINE CONTROL ZONE
Your lawn mower is equipped with an operator
presence control bar which requires the operator to
be positioned behind the lawn mower handle to start
and operate the lawn mower.
06
TO OPERATE DRIVE SYSTEM(See Fig.6)
To start forward motion, lift drive control bar up to
handle.
Fig.6
Engine throttle
control lever
Start
Slow
Fast
Engine brake handle/Blade brake handle(Model with BBC)
Drive speed control lever
Engine
Wheel
Bumper
Chassis
Upper handle
Rear cover
Grass catcher
Starter knob
Throttle and drive controler
Height adjustment lever
Locking lever
Adjuster
Height adjustment lever
Height adjustment lever
Locking lever
Air filter
Fig.8
To stop forward motion, release drive control bar.
IMPORTANT
: ALWAYS KEEP DRIVE CONTROL
FULLY ENGAGED AGAINST HANDLE WHEN IN USE.
TO ATTACH GRASS CATCHER
1.
Lift the rear door of the lawn mower and place the
grass catcher frame side hooks into the slots of the
rear door.
2.
The grass catcher is secured to the lawn mower
housing when the rear door is lowered onto the grass
catcher frame.
stop
start
forward
-First press the lever slightly downwards and adjust
to the desired speed. The lever automatically clicks
back into the nearest new position.
-Position
rabbit
=fast(max.speed)
-Position
tortoise
=slow (min.speed)
All four wheels are adjusted by a single lever except
the model 2in1. The 2in1 mower has two levers to
adjust the front wheel and rear wheel individually.
You can set the cutting height to the desired height
to fit different terrain. Pull the lever out from the catch,
move to the desired position and let it fall back into
the catch.
WARNING: The lawnmower can only be used on
level lawns if the lowest cutting height is being
used.
NOTE: The speed may only be adjusted
ADJUSTING THE DRIVE SPEED (See Fig.8)
for speed adjustable model
w h e n t h e e ng i n e i s r u n ni n g i n o r de r t o
a vo i d d am a g e !
-The driving speed can be continuously adjusted by us-
ing the adjustment lever mounted on the upper hand.
WHEEL ADJUSTER
LEVER
Fig.9
Fig.10
ENGAGE THE BLADE-CLUTCH (See Fig.7)
only for machines with BBC
Fig.7
Blade clutch lever
running.
The mower is adjusted to one cutting height upon
delivery.
Never adjust the cutting height with the motor still
ADJUSTING THE CUTTING HEIGHT (See Fig. 9)
Fig.6
Upper handle
Step 1
Step 2
Slow
(tortoise)
Fast
(rabbit)
Drive speed
control lever
for low cut
Raise wheels
for high cut
Lower wheels
for high cut
Lower wheels
for low cut
Raise wheels
WHEEL ADJUSTER
LEVER
CENTRAL ADJUSTER ON RIGHT SIDE
ADJUSTER ON EACH WHEEL
2.Press the blade-clutch-lever close to the handle-
bar completely to engage blade.
3.Release the lever about 2'' away from the hand-
lebar, until the lever make a 'click' sound. And
then re-press the lever and hold it togather with
the handlebar.
4.Release the blade-clutch-lever completely to
dis-engage and stop the blade.
1. For safety, the blade-clutch-lever can not be en-
gaged directly after releasing. Push the lever
forward until it make a 'click' sound, and then
you can engaged the clutch again.
