background image

                 www.weg.net 

 

 

 

14    l

  

Installation, operation and maintenance manual – Squirrel cage motor – WGM20 Line                                                 14108242

 

3

 

RECEIVING, HANDLING AND STORAGE 

 

3.1

 

RECEIVING 

 

All motors were tested and are in perfect operating 
conditions. The machined surfaces are protected against 
corrosion. The package must be inspected upon receipt 
for occasional damages during transportation.   

 

 

ATTENTION 

Any damage must be photographed, 
documented and reported immediately to the 
carrier, the insurer and WEG. The non-
communication of this damage will void the 
warranty.

 

 

 

ATTENTION 

Parts supplied in additional packages must be 
checked upon receipt. 

 

 

 

When lifting the package (or container), the proper 
hoisting points, the weight indicated on the package or 
on the nameplate and the operating capacity and 
conditions of the hoisting equipment must be observed; 

 

Motors packed in wooden crates must always be lifted 
by their own lifting lugs or by a proper forklift; they must 
never be lifted by the package; 

 

The package can never be overturned. Place it on the 
floor carefully (without impact) in order to avoid damage 
to the bearing; 

 

Do not remove the grease for protection against 
corrosion from the shaft end, or the closing plugs 
present in the terminal box holes. These protections 
must remain in place until the moment of the final 
assembly. 

 

A complete visual inspection of the motor must be 
carried out after removing the package;  

 

The shaft locking system must be removed just before 
the installation and stored to be used in future 
transportation of the motor. 

 

3.2

 

HANDLING 

 

 

ATTENTION 

 

In order to move or transport the motor, the 
shaft must be locked with the locking 
device supplied with the motor. 

 

Lifting equipment and devices must be able 
to withstand the motor weight.

 

Failure to comply with these 
recommendations may cause damage to the 
equipment, personal injuries or both.

 

 
 
 
 
 
 
 

 

NOTES 

 

Observe the indicated weight. Do not lift 
the motor causing jolts or put it down 
abruptly on the floor, because  this may  
cause damage to the bearings;  

 

In order to lift the motor, use only the lifting 
lugs provided for that purpose. If 
necessary, use a crossbeam to protect 
parts of the motor. 

 

The lifting lugs on the heat exchanger, end 
shields, bearings, radiator, terminal box, 
etc. are designed to handle these 
components only separately;  

 

Never use the shaft to lift the motor; 

 

The frame lifting lugs are intended to lift 
only the motor. Never use them to lift the 
motor-driven machine set. 

 

 

3.2.1

 

Horizontal motor handling 

 
Horizontal motors must be handled as shown in Figure 
3.2.
 
In order to lift the motor, use only the lifting lugs provided 
for that purpose. 
 
CABLES GUIDE            

 

TERMINAL BOX 

 

 

 

Figure 3.1: Horizontal motor handling

 

 

 
Remove the cable guide and lift the motor, as shown in 
Figure 3.2. 
 

 

Figure 3.2: Motor handling

 

 
 
 
 
 
 
 
 
 
 

LIFTING LUGS 

Содержание WGM20 Series




















































Отзывы: