PIN CABLE CONNECTING
E-RING, D8
PLATE ASS'Y
FLANGE
PLATE BAR TAB
ADJUSTING NUT
ACW800
-HOLE
LOWER ADJ NUT
<Detail. A>
GROOVE
HOLDER
FLANGE CABLE
M ¿10 SCREW
5
CABLE MOUNTING NUT
CABLE ROD
FIXED TAB PLATE
LINK ASS'Y
PLATEASS'Y
BASEFHU
<Fig. 4>
<Fig. 5>
<Fig. 6>
PLATE ASS'Y,
BASE FHU
Tap
UNC
1/4"-20
1/4"-20
UNC 2A
Mounting Screw
-Dimensions : inch
(mm)
1/4, NUT
ENCLOSURE
DOOR
1.
(
)
71
43.6
1.
(
)
48
37.6
1.
(
)
16
29.7
1.
(
)
12
28.4
1.988
50.5
(
)
1.1
28
(
)
2.36
60
(
)
0.09
2.3
(
)
2.598
66
(
)
1/4 in
2 Screws
2.32
59
(
)
3.72
94.6
(OFF)
(
)
3.14
(
)
79.65
(ON)
1.72
43.6
(
)
2.7
68.6)
(
8.66
2 0
( 2 )
MANUAL INSTRUCTION ACW800 FHU
PLATE HOOK LOCK
3. BREAKER AND BREAKER OPERATOR INSTALLATION-See Figure. 5
1. Turn the circuit breaker ON.
2. Attach circuit breaker and PLATE ASS'Y,BASE FHU to the back
panel using four N .1/4"-20 UNC screws as shown at Figure 5.
Tighten screws to 150 in-lbs.
O
3. Attach the PLATE FIXED CABLE TO PLATE ASS`Y BASE FH3
using M5x10 screw. Tighten screws to 25 in-lbs.
*
DANGER- Confirm that suppling power has been turned off.
* CAUTION-DON'T PUSH TRIP BUTTON WITH FINGERS.
4. CABLE INSTALLATION - See Figure. 6
1. Secure cable to PLATE ASS'Y FLANGE with HOLDER FLANGE
CABLE using M5X10 screws. Tighten screws to 75 in-lbs.
HOLDER FLANGE CABLE must interlock with groove in cable.
2. Move handle to OFF position and pull cable to it's maximum stroke
Shim cable connecting and attach into hole of LINK ASS'Y.
Secure with E-ring.
3. Attach end of cable to PLATE ASS'Y BASE FHU as described below.
NOTE: To ensure proper adjustment and to prevent possible damage to
the operator, Follow the remaining steps carefully.
4. Move the handle to it's maximum ON position.
5. Adjust the top cable mounting nut to M5 from start of cable thread as
shown in Detail A.
6. Insert end of the cable rod through the hole in the PLATE BAR TAB
And place the cable mounting threads into the slotted FIXED TAB
PLATE of the PLATE ASS'Y BASE FHU. Tight cable mounting nut
(M12) And adjustment nut (M12) until the cable is secured to the tab.
7. After install the mounting nut and adjustment nut. Handle is maximum
On position.
5. CABLE ADJUSTMENT
1. Check that the circuit breaker turns OFF and ON by moving the
operating handle. If circuit breaker does not turn ON, loosen adjusting
nut and tight lower adj nut to PLATE BAR TAB.
Repeat if required.
2. Turn the circuit breaker ON and trip it by pushing the "trip" button (not
using your finger).
3. If the circuit breaker does not reset, loose the lower adj nut and tight
adjusting nut to PLATE BAR TAB.
Repeat if required.
* DANGER- Confirm that suppling power has been turned off.
* CAUTION-DON'T PUSH TRIP BUTTON WITH FINGERS.
