Operate the light
Press the buttons B and hold it down for more than 2
seconds
Switch mode
(ON state) Press and immediately release the Button A
Trigger flash
Press and immediately release the Button A（it does not include
synchronization mode）
S1=Single trigger mode S2=Double trigger mode
SH=Synchronous mode
Red light
Wide light
Brightness adjustment
(Adjustment knob A) Rotate clo,
Wide light: Totally 10 levels from 0 to 100, A level is 10%，
Brightness adjustment（Flash）
(Adjustment knob A) Rotate counterclockwise-,
Wide light: Totally 10 levels from 100 to 0,
(Adjustment knob B) Rotate counterclockwise-,
(Flash index level: 24→22→16→11→8→5.6→4→2.8→2→1.4→ 1)
(Adjustment knob A) Rotate clo,
On S1/S2 mode ( it does not include synchronization mode）
Strobe mode
On S1 mode, Flash light flashes when a single flashing signal is received.
On S2 mode, Flash light flashes when two flashing signals are received
within 1 second.
On HS mode, (it must be connected to fiber optic cable) received flash
signal, according to the letter To flash.
On normal mode, the current state will be recorded when the
machine is shut down, and the same state will be recorded when
the machine is turned on again.
(the remote control button for the first time is invalid)
Press the middle
button and hold it down for more than 2seconds
Press and immediately release the middle button (On Flash mode)
Press and immediately release the middle button (On LED mode)
Memory function
Function of remote control
When the battery voltage is too low, all the Buttons are invalid and
can only be turned off.
Low power protection
1. Insert the DC charger plug into the battery.
2.Plug the charger into the wall receptacle. When the battery
beings to charge the indicator light on the charger will be red.
3.When the battery is fully charged the indicator light on the
charger will turn green.
To Charge the battery
Turn ON
（OFF state） Press and immediately release the Button A ，
Turn OFF
(ON state) Press the buttons A and hold it down for more than 2
seconds
（OFF state），Press the buttons A and B at the same time adjust
the screen orientation mode（forward show and backward show）,
Press and immediately release the Button A enter the screen mode，
Press the buttons A and hold it down for more than 2 seconds
FlASH MODE
LED MODE
DC charger plug
General Maintenance
There two-rings in the tail cap. Use silicone to keep the O-rings
well lubricated. It is important to lubricate the o-rings if the
flashlight has not been used in a long time or if the o-ring is
hard. If the O-ring is damaged, broken or deformed it should
be replaced with the spare.
Note：Do not use a sharp tool to remove the O-rings.
Warning
1.Do not open the tail cap when the video light is in the water.
2.Do not shine the light directly into your eyes or another
person’s eyes.
3.Do not touch the battery and charger with wet hands.
4.Use only the manufacturer’s battery and charger with this
system.
5.If the flash light will not be used for a long period of time the
battery should be removed.
Failure to comply with these warning may result in damage
to the video light and will nullify the warranty.
Warranty
We provides a warranty against manufacturer defects for 1 year
starting from the date of purchase. Manufacturer defects occuring
within 15 days of the date of purchase will result in an exchange of
product at the vendor. All other manufacturer defects occuring
within 1 year of the purchase will be repaired at no cost. Proof of
purchase is required for warranty support. The warranty does not
cover failures or defects resulting from misuse (e.g; modification;
damage), natural disasters, or battery issues, including incorrect
battery installation.
07
06
05
04
Red light
Wide light
S1
S2
SH
S1
S2
SH
