background image

6

OPERATING INSTRUCTIONS

OPERATING POSITION

Eye Protection

Long Pants

Heavy Shoes

ALWAYS WEAR:

Cut from your right to your left.

WARNING:

Always wear eye protec-

tion. Never lean over the trimmer head.
Rocks or debris can ricochet or be thrown into
eyes and face and cause blindness or other
serious injury.
Do not run the engine at a higher speed than
necessary. The cutting line will cut efficiently
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise and
vibration. The cutting line will last longer and will
be less likely to “weld” onto the spool.
Always release the throttle trigger and allow the
engine to return to idle speed when not cutting.
To stop engine:

S

Release the throttle trigger.

S

Move the ON/OFF switch to the OFF posi-
tion.

TWIST AND EDGE

The Twist and Edge feature allows for easy
edging of sidewalks, patios, driveways, etc.
1.

Pull the tab toward the engine.

2.

Twist the tube to the edging position; re-
lease tab.

Tab

TRIMMER LINE ADVANCE

The cutting head advances line automati-
cally. Do not tap head on the ground to ad-
vance line. 
This may break parts and cause
cutting head to malfunction.
Upon unit start up, the line will advance auto-
matically to the correct cutting path length.
Always keep the shield in place when the tool
is being operated.

WARNING:

Use only 0.080” (2 mm)

diameter round line. Other sizes and shapes
of line will not advance properly and will result in
improper cutting head function or can cause se-
rious injury. Do not use other materials such as
wire, string, rope, etc. Wire can break off during
cutting and become a dangerous missile that
can cause serious injury.

CUTTING METHODS

WARNING:

Use minimum speed

and do not crowd the line when cutting around
hard objects (rock, gravel, fence posts, etc.),
which can damage the trimmer head, become
entangled in the line, or be thrown causing a
serious hazard.

S

The tip of the line does the cutting. You will
achieve the best performance and mini-
mum line wear by not crowding the line into
the cutting area. The right and wrong ways
are shown below.

Tip of the Line
Does The Cutting

Right

Line Crowded Into
Work Area

Wrong

S

The line will easily remove grass and
weeds from around walls, fences, trees and
flower beds, but it also can cut the tender
bark of trees or shrubs and scar fences. To
help avoid damage especially to delicate
vegetation

or trees with tender bark,

shorten line to 4--5 inches (10--13 cm) and
use at less than full throttle.

S

For trimming or scalping, use less than full
throttle to increase line life and decrease
head wear, especially:

S

During light duty cutting.

S

Near objects around which the line can
wrap such as small posts, trees or fence
wire.

S

For mowing or sweeping, use full throttle for
a good clean job.

TRIMMING -- Hold the bottom of the trimmer
head about 3 inches (8 cm) above the ground
and at an angle. Allow only the tip of the line to
make contact. Do not force trimmer line into
work area.

Trimming

3 inches (8 cm)
above ground

SCALPING -- The scalping technique re-
moves unwanted vegetationdown to the
ground. Hold the bottom of the trimmer head
about 3 in. (8 cm) above the ground and at an
angle. Allow the tip of the line to strike the
ground around trees, posts, monuments, etc.
This technique increases line wear.

Содержание TWIST-N-EDGE TE400CXL












Отзывы: