background image

6

S

Insert a hex wrench into aligned holes. This

will keep the shaft from turning while tight-

ening the trimmer head.

Hex Wrench

S

While holding the hex wrench in position,

thread trimmer head onto the shaft and

tighten until secure.

NOTE:

The retaining washer must be posi-

tioned with the raised section facing toward

the gearbox.

ASSEMBLY INFORMATION --

BRUSH BLADE

BRUSH

BLADE

NOTE:

If your unit has been assembled for

trimmer head use, refer to the section ATTACH-

ING THE PLASTIC SHIELD AND TRIMMER

HEAD and reverse the steps to remove the

plastic shield and trimmer head before you

mount the metal shield and blade. Store these

parts for future use. Never use the trimmer head

with the metal blade installed.

ASSEMBLY OF THE METAL SHIELD

DANGER:

The metal shield must be

properly installed on the tool anytime the tool

is used with the blade. The forward tip of the

metal shield helps to reduce the occurrence

of blade thrust which can cause serious injury

such as amputation to the operator or by-

standers. Failure to install the shield in the

position shown can result in serious injury to

the operator. The length of the shield must be

aligned with the length of the tube.

DANGER:

The blade is sharp and can

cut you. Be sure to wear gloves while working

with blades.

S

If your unit has a plastic cover over the

threads on the shaft, remove the covering

to expose the threads.

S

Place the metal shield under the gearbox,

and align the screw holes.

Shield

Gearbox

S

Insert the 4 mounting screws through the

bottom of the shield. Thread them into the

gearbox. Tighten evenly and securely with

one of the hex key wrenches provided.

ASSEMBLY OF THE METAL BLADE

WARNING:

Do not use any blades, or

fastening hardware other than the washers and

nuts illustrated in the following illustrations.

These parts must be provided by Weed Eater,

and installed as shown below. Failure to use

proper parts can cause the blade to fly off and

seriously hurt you or others.

NOTE:

When installing the blade, make sure

you install it with the correct side facing up

(marked on the blade). If you are re-installing

an older blade and the writing has worn off,

use the following illustration as a guide.

Teeth on

blade point in

this direction

Top view of blade

NOTE:

The dust cup and retaining washer

are located on the gearbox and not in the

parts bag.

S

Remove the retainer washer from the gear-

box, and leave the dust cup on the gearbox.

NOTE:

It may be necessary to remove a

plastic protective covering from the

threaded shaft before removing the retain-

ing washer.

Retaining

Washer

Dust Cup

S

Install the blade over the threaded shaft ex-

tending from the gearbox between the dust

cup and the retaining washer. Make sure

Содержание BC3100













Отзывы: