Weed Eater 530087645 Скачать руководство пользователя страница 10

Страница: 10 / 12

SERVICE

We recommend all service and adjustments

not listed in this manual be performed by an

Authorized Service Dealer.

CARBURETOR ADJUSTMENT

Your carburetor is equipped with limiter caps.

Damage will occur if you turn the needles be-

yond the limiter caps. Carburetor adjustment is

a complicated task. We recommend that you

take your unit to an Authorized Service Dealer.

SPARK PLUG

Replace spark plug yearly with a Champion

CJ-8Y plug; spark plug gap is .025 in.

IGNITION TIMING

Ignition timing is fixed, non-adjustable.

NEED ASSISTANCE?

Call 1-800-554-6723 for assistance.

NEED SERVICE PARTS?

Contact your dealer or call 1-800-554-6723.

TROUBLE

CAUSE

REMEDY

Engine will not

start.

Engine flooded.

Fuel tank empty.

Spark plug not firing.

Fuel not reaching

carburetor.

Carburetor requires

adjustment.

See “Starting Instructions.”

Fill tank with correct fuel mixture.

Install new spark plug.

Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

See “Carburetor Adjustments.”

Engine will not

idle properly.

Carburetor requires

adjustment.

Throttle trigger problems.

See “Carburetor Adjustments.”

Contact an Authorized Service Dealer.

Air filter dirty.

Spark plug fouled.

Carburetor requires

adjustment.

Engine will not

accelerate,

lacks power, or

dies under a

load.

Clean or replace air filter.

Clean or replace spark plug

and re-gap.

See “Carburetor Adjustments.”

Engine smokes

excessively.

Fuel mixture incorrect.

Air filter dirty.

Carburetor requires

adjustment.

Empty fuel tank and refill with

correct fuel mixture.

Clean or replace air filter.

See “Carburetor Adjustments.”

Engine runs hot

Fuel mixture incorrect.

Spark plug incorrect.

Carburetor requires

adjustment.

Empty fuel tank and refill with

correct fuel mixture.

Replace with correct spark plug.

See “Carburetor Adjustments.”

TROUBLESHOOTING TABLE

WARNING:

Always stop unit and disconnect spark plug before performing any of

the recommended remedies below other than remedies that require unit to be operating.

Line does not

advance or

breaks while

cutting.

Line welds

onto spool.

Line pulls

back into

head.

Line improperly routed in

head.

Line improperly would

onto spool.

Incorrect line size.

Not enough line outside

of head.

Dirt buildup on cover.

Check line routing.

Rewind line tightly and evenly.

Use only 0.080” diameter line.

Pull 4 inches of line outside of head.

Clean cover.

Incorrect line size.

Incorrect spool.

Line is being crowded

against material being

cut.

Use only 0.080” diameter line.

Replace with correct spool.

Cut with tip of line fully extended.

Too little line outside of

head.

Line size incorrect.

Remove cover and pull 4 inches

of line outside of head.

Use only 0.080” diameter line.

Содержание 530087645













Результаты поиска

Содержание 530087645

Отзывы:

Weed Eater 530087645, Руководство оператора, Страница: 10 / 12

Результаты поиска

Содержание 530087645

Отзывы: