background image

7

4. Safety

General

All safety instructions must be read and complied with, as 

non-compliance will result in

 

 

-  Danger to life and limb of the user,

 

-  Impairments to the machine or other property.

In addition to the operating manual, the accident-prevention 

regulations in the country where the appliance is used must 

be  complied with. 

Intended use

Non-intended use

Residual risk

There is always an increased risk of accidents in the imme-

diate danger area around the machine if the operator fails to 

notice persons in the vicinity of the machine. 

Make anyone close to the machine aware of this risk. 

The operator must not put the machine into operation unless 

everyone in the vicinity of the machine is aware of this risk. 

The machine should only be used in technically faultless 

condition, as intended, in a safety-conscious and hazard-

conscious manner, and in compliance with the instructions 

in the operating manual. 

Malfunctions that may impair safety require that you stop 

working with the machine immediately. These types of damage 

must be reported and corrected without delay.  

The machine is designed exclusively for compacting:

 

-  paving slabs made of concrete.

The operator's work position is behind the machine.

The operator must guide the machine safely with both hands 

on the handle.

Unless used as intended, the machine involves a risk of per-

sonal injury and property damage. The machine is expressly 

not suitable for:

 

-  compacting frozen subsurfaces,

 

-  compacting hard soils that cannot be compacted 

 

further,

 

-  compacting non-bearing material,

 

-  compacting highly cohesive soils,

 

-   Sand,

 

-   Gravel,

 

-   Asphalt.

 

The responsibility for any damage arising from non-intended 

use falls on the owner / operator.

Non-intended use or misuse will void all liability and warranty 

claims.

Содержание 0105001





























Отзывы: