manualshive.com logo in svg

Webasto Thermo Pro 90 D, Руководство по установке

Поделиться
Скачать
Webasto Thermo Pro 90 D Скачать руководство пользователя страница 33

Webasto Thermo & Comfort N.A., Inc.

34

www.techwebasto.com

Initial Start-up

Thermo Pro 90

13. Initial Start-up

IMPORTANT!

Refer to the safety instructions in the operating and maintenance instructions.
The operating and maintenance instructions must be read thoroughly before starting the heater.

HEATER MOUNTING

Complete

(Yes/No/Comments)

1

Is the heater installation safely secure / rigid?
(Ensure that all bracket bolts are tight)

2

Is there a safe clearance from heat generating
Components? (I.e. exhaust, etc...)

3

Is there sufficient clearance between heater and any
vehicle moving components under all operating 
conditions? (steering cranked to extreme positions,
torqued engine, suspension, etc...)

4

Is the heater mounted in an acceptable position
according to the limitations noted in the 
installation manual?

5

Is the heater installed in a protected location from 
road debris and splash-water or items stored in the same area?

6

Is there a sufficient amount clearance
between the heater and the ground? (Coolant heaters only)

COOLANT SYSTEM

Complete (Yes/No/

Comments)

1

Is there a safe clearance (min 4 in.) from heat generating components? 
(exhaust, etc...)

2

Is there a safe clearance from sharp edges / objects?
Ensure a heat protective has been installed (if applicable)

3

Are there any kinks, sharp bends or the possibility for pinched hoses or 
harnesses, cuts and rub through?

4

Have all the hose clamps been properly positioned and tightened?

5

Has the coolant system been topped off and bleed per the

 vehicle 

manufacture’s specifications for proper mixture and type?

6

Has a pressure test been performed on the coolant system under all 
operating conditions?

7

Have the coolant hoses been installed so that they are below the coolant 
filler cap?

8 

Has the coolant flow direction been verified?

Содержание Thermo Pro 90 D













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды