Webasto D5W Z Скачать руководство пользователя страница 9

Galaxy

D5W Z heater upgrade

9

Permanent positive connection

For all vehicle

The permanent positive connection is made at plug C6 
(1) on the central electrics box P91

- Disconnect plug C6 (1)

Make the connections using the supplied 3-way 
distributor (5), blade-type plug sleeves and insulation 
sheaths as shown in the figure and the circuit diagram 
in Figure 3 or 4.

- Use the supplied blade receptacles with detent

points

- Disconnect the red cable (1, 4) from the standard

wiring harness (6)

- Cut the red cable (1) from the standard main blade-

type fuse F 106, 110 A, to plug C6 (supply to
standard blade-type fuses F51 to F54) as shown in
the figure

IMPORTANT
The black insulation sheath is used on the blade-type 
plug sleeve on the red cable (1) of the standard main 
blade-type fuse!

- Connect both standard red cables (1, 4) and the red

cable (2) (supply to the Webasto wiring harness) as
shown in the figure using a 3-way distributor (5)

- Insulate the wiring harness (6) again and reconnect

plug C6 (3)

Earth connection

The earth connection is made on the standard earth 
post (1) on the left above the fuse/relay holder.

- Secure the earth cable to the earth post (1)

1

11

4

2

3

1

6

5

12

1

13

Содержание D5W Z

















Отзывы: