Webasto BBW 46 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 18

Webasto BBW 46 Скачать руководство пользователя страница 12

Installation of Antenna

NOTE:
Preferably, the antenna should be installed in the interior
of the vehicle, at the top in the centre of the windshield or
rear window. If installed at different locations, the range is
likely to be diminished.

For an optimal reception, a distance of 2

±

0.5 cm from the

windshield edge is to be maintained (Fig. 15). The cable
should be routed upward, beneath the panelling in the ve-
hicle roof and then directed to the right or left to the
chassis member.

NOTE:
In the case of lack of space, the antenna may be installed
up to 15 cm off-centre.

- Clean windshield or rear window using grease-dissolv-

ing cleaner (e.g. methylated spirits).

- Peel off protective film from antenna and glue antenna

in place.

NOTE:
Do neither shorten nor sharply bend antenna cable.

- Route antenna cable to receiver.
- Establish plug connection at receiver and tighten con-

nector hand-tight.

- Secure antenna cable using cable ties.

2

±

0.5 cm

Antenna

Fig 15:

Installation of Antenna

BBW 46 / DBW 46

10

«
...
10
11
12
13
14
...
»

Содержание BBW 46



















Отзывы:

Нет отзывов