background image

 

 

7.

 

Improper installation or repair of Webasto heating systems can cause 

fire or the leakage of deadly carbon monoxide leading to serious injury 

or death. 

8.

 

The heater must be checked by an expert at the latest at the start 
of the cold-weather period. 

9.

 

NEVER attempt to install or repair a Webasto heating system unless you 

have successfully completed Webasto factory training and have the 

technical skills, technical information, tools, and equipment required to 

properly complete the necessary procedures. Only genuine Webasto 

parts may be used. 

10.

 

In the event of a long-term heavy smoke condition, unusual 

combustion noises, the smell of fuel, or if the heater suffers 

continuous faults with error messages (flashing code), it must be 

shut down by removing the fuse and must not be reused until it 

has been inspected by Webasto- trained personnel. 

11.

 

Webasto products produce temperatures high enough to ignite 

surrounding combustible materials such as inflammable liquids, gases, 

vapor, and other combustible matter. The heater must be switched off 

when loading or unloading inflammable materials to prevent the risk of 

explosion. 

12.

 

The heat transfer unit on air heaters is exposed to very high 

thermal stress and must be replaced by a genuine Webasto spare 

part ten years after it is used for the first time. 

If exhaust lines pass through areas used by personnel, they 

must also be replaced by genuine spare parts after ten years. 

13.

 

The fuel specified by the vehicle manufacturer is suitable for use in the 

Air Top 2000 ST B (gasoline). 

14.

 

The diesel fuel specified by the vehicle manufacturer is 

suitable for use in the Air Top 2000 ST D (diesel). 

15.

 

There are no known negative influences due to fuel additives when 

used appropriately. 

16.

 

If fuel is extracted from the vehicle’s tank, follow the additive 

instructions issued by the vehicle manufacturer. 

17.

 

If you change to low-temperature fuel, the heater must be operated 

for approx. 15 minutes so that the fuel system is filled with the new fuel. 

18.

 

The temperature in the area around the heater must not 

exceed 85 °C / 185° F (storage temperature). If the temperature 

exceeds this level there is a risk of permanent damage to the 

electronics systems. 

19.

 

Webasto rejects any liability for problems and damage caused by the 

system being installed by untrained personnel. 

20.

 

Keep the hot air inlet and hot air outlet free of dirt and 

foreign bodies. Soiled or blocked hot air lines may cause 

overheating. 

21.

 

To prevent mechanical parts seizing, the heater should be operated for 

Содержание Air Top Series















Отзывы: