background image

ELITE 600 V1.0 

A. Important Notice

 

 

Before setting up and operating the instruments, please carefully read these instructions to 

get familiarized with the installation and operation process. Instructions should be read by 

experienced individuals before operating the instruments.     

Any improper usage of the instruments may cause damage. Please refer to the safety 

notice included with this equipment. 

The instruments shall not be modified or altered in any way. Any modification or alteration 

will void the warranty, void the regulatory certifications and create potential safety hazard. 

Wealtec is not responsible for any injury or damage caused by using the instruments for any 

non-intended purpose or injury as a result of modification of the instruments by any person who 

is not authorized by Wealtec Corp.   

 

A-1. Warranty 

 

ELITE 600 are warranted to be free from defects in materials or workmanship for a period 

of one year from the original invoice date, under normal usage. Any defects occurring during 

warranty period, Wealtec Corp. will repair or replace defective products or parts without charge 

unless the defects arise from conditions outlined below. The defects described below are 

specially excluded from Wealtec warranty policy.   

1.  Improper operation of the instrument. 

2.  Repair or modification by any person who is not authorized by Wealtec Corp.   

3.  Damage caused by any (in)-direct accident, neglect or misuse. 

4.  Damage caused by disaster.   

5.  Damage caused by any improper solvents or samples 

 

A-2. Technical and Service Contact 

 

Most of the operation details are described in this instruction manual to assist and guide 

operator for an appropriate solution. For any other technical/ service questions, please contact 

your local representative or contact Wealtec international technical/ service specialist by E-mail: 

[email protected]

 

  1

Содержание ELITE 600
















Отзывы: