WE-EF FLD121 Скачать руководство пользователя страница 2

Installation

 

The product must be installed and maintained by a suitably 
qualified person in compliance with the latest applicable 
regulations and relevant legislation

The minimum distance of an object to be illuminated must be 
observed (see illustration             inside FLD131 but FLD121  
doesn’t require a minimum distance).

 

Claims based on defects attributable to improper installation, 
application, operation and/or any modification carried out by the 
purchaser or third parties, and the consequences thereof, are 
excluded.  

Important:

 The luminaire is factory-sealed and does not need to be 

opened during installation. 

2)

Installation method 2 for column fitter

Installation Procedure

 

1)

Installation method 1 for flat surface fitter

Fig. II 

Wiring diagram 1-10 V analogue dimming interface

 

Flat Surface Fitter 

o

Suitable for column diameter 

 76 mm.

Service door on column has to be provided for cable

termination (maximum 1.5 m from column fitter mounting

position).

2.1 Switch off mains electrical supply.

2.2 Determine position for fixing screws 

D

 and cable entry

 

hole

 F

. Drill relevant holes 

E

 and 

F

 on column

 X

. Ensure

 

cable entry hole

 F

 is of sufficient diameter to feed cable 

C

 

from luminaire

 A

 through.

2.3 Set and fix column fitter 

B

 in position. Insert and tighten

 

screws 

firmly.

2.4 Feed cable 

C

 from luminaire

 A

 

through pivot 

I

 and cable

 

entry hole 

F

 on column

 X,

 while connecting luminaire 

A

 with

 

column fitter

 B

 by sliding slip

 

fitter 

over pivot 

I

. Turn

 

luminaire 

A

 towards object to be illuminated. Ensure the

 

slip

 

fitter

 H

 is properly seated on pivot

 I, 

then tighten screw

 

M

 

firmly.

2.5 Check that rating shown on luminaire label conforms

 

with mains electrical supply.

2.6 Mains supply cable 

C to be connected to incoming 

supply using terminations supplied by others.

2.

7

 Loosen screw 

N

 slightly. Then aim luminaire in desired 

direction and tighten screw 

firmly. 

 

Tighten set screw    .

O

1.1 Switch off mains electrical supply.

1.2 

Detach strain relief clip

 K

 out of flat surface fitter

 B.

 

Important:

 Keep strain relief clip

for locking cable later.

(item 1.6 in this installation instruction)

1.3 Feed cable 

C

 from luminaire

 A

 through pivot 

and hole 

L

 

of flat surface fitter

 B

.

1.4 Determine positions for two fixing screws 

D

. Drill relevant

 

holes 

E

 and insert heavy duty wall plugs

 F

. Insert and tighten

 

screws 

D

.

Caution:

 Make sure not to damage any electric cable, water

 

pipe or other devices while drilling holes.

1.5 Release screw

 M

 on slipfitter 

H

 (do not turn it out) until

 

the splipfitter is split out slightly. Connect luminaire 

A

 with

 

flat surface fitter

 B

 by sliding slipfitter 

over pivot 

I, 

while

 

pulling cable 

C

 through hole

 L 

and turning luminaire 

A

 

towards object to be illuminated. Ensure slipfitter

 H

 is

 

properly 

seated on pivot

 I, 

then tighten screw 

M

 firmly.

1.6 Clamp 

strain relief clip

 K

 on the cable 

C

 and press into 

the

 

hole 

L

 of flat surface fitter

 B.

 Ensure the strain relief clip 

is

 

properly placed in position to lock the cable. (fig.I)

1.7 Check that rating shown on luminaire label conforms

 

with 

mains electrical supply.

1.8 

Mains supply cable C to be connected to incoming supply 

using terminations supplied by others.

1.9 Loosen screw 

N

 slightly. Then aim luminaire in desired

 

direction and tighten screw 

firmly.

 

Tighten set screw    .

O

Fig. I  

Strain relief clip locking

 

Отзывы: