WCP SS Swerve (BLDC) Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 39

WCP SS Swerve (BLDC) Скачать руководство пользователя страница 11

WCP SS Swerve (BLDC)- User Guide

(Rev 1)

Page 11

WCP SS Swerve (BLDC)- User Guide (Rev 1)

wcproducts.com

Wheel Module - Step 3

The drive shaft and all the components on the shaft should be inserted first. The wheel

module drive shaft goes into the 3/8”ID bearing. The 1/4”ID x 1/2”OD bearing should be

able to be pressed in by hand into the forks. Only the fork that that aligns with the drive

shaft needs a bearing.

Note: Roll pins are optional and not included in the kit�

The roll pins should be tapped into the forks using a hammer. We recommend holding

the fork in a bench vise to do this. The roll pins will be tight fit into the 72T gear. This is

intended and you can use the #10-32 bolts to pull everything together. If a slip fit is pre

-

ferred for the roll pins, the holes in the 72T gear may be drilled out for a slip fit. This is

acceptable as well.

Note: Do not forget to insert key before putting the 8mm snapring on�

«
...
9
10
11
12
13
...
»

Содержание SS Swerve (BLDC)








































Отзывы:

Нет отзывов